Agilent Technologies EasyEXPERT Guide de l'utilisateur Page 130
- Page / 228
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
9-4 Agilent EasyEXPERT User’s Guide Vol. 2, Edition 1
If You Have a Problem
When You Operate B1500
ASU is not Detected
If Agilent B1500A/EasyEXPERT cannot detect ASU (atto sense/switch unit), turn
the B1500A off, check the cable connection, and reboot the B1500A/EasyEXPERT.
For the installation and connection of ASU, see Agilent B1500A User’s Guide.
NOTE
Connect ASU to dedicated SMU
The specifications are satisfied and guaranteed for the exclusive combination of the
ASU and the SMU. So confirm the serial number of the ASU and connect it to the
dedicated SMU properly.
N1265A/N1266A/N1268A is not Detected
If Agilent B1505A/EasyEXPERT cannot detect any of the following fixtures, turn
the B1505A off, check the cable connection, and reboot the B1505A/EasyEXPERT.
• N1265A Ultra High Current Expander/Fixture
• N1266A HVSMU Current Expander
• N1268A Ultra High Voltage Expander
For the installation and connection of these fixtures, see Agilent B1505A User’s
Guide and Configuration and Connection Guide.
External GPIB Devices are not Detected
If Agilent B1500/EasyEXPERT cannot detect external GPIB devices, do the
following troubleshooting.
1. Turn the B1500 and external GPIB devices off, check the GPIB cable
connection, and reboot the devices and the B1500/EasyEXPERT.
2. If the problem still remains, confirm if the B1500 is set to the system controller.
See Agilent B1500A or B1505A User’s Guide to enable the system controller.
3. If the problem still remains, confirm if the B1500 is connected to USB0. Open
Agilent Connection Expert, check Instrument I/O on this PC. The USB0 in this
area must show the information as shown below.
USB0
+ B1500A(USB0::xxxx::x::xxxx::x::INSTR)
+ agb1500a
+ UsbDevice1
- Keysight EasyEXPERT Software 1
- For B1500A Users 5
- For B1505A Users 5
- In This Manual 6
- Contents 10
- 6 Remote Control Interface 13
- Sample programs 14
- About socket services 14
- Introduction 15
- Supported Operations 16
- Preparation for Communication 17
- Common Commands 22
- BENCh Subsystem 23
- [:BENCh]:COUNt:RESet 24
- [:BENCh]:LOAD[:SETup] 24
- [:BENCh]:PRESet:CATalog? 24
- [:BENCh]:PRESet:OPEN 24
- [:BENCh]:PRESet:SETup:SELect 25
- [:BENCh][:SELected]:ABORt 26
- [:BENCh][:SELected]:NAME 26
- [:BENCh][:SELected]:NUMBer 26
- [:BENCh][:SELected]:STRing 27
- [:BENCh]:TAG 28
- CALibration Subsystem 29
- :CALibration[:SMU]:ZERO[:ON] 30
- :CALibration[:SMU]:ZERO:PLC 31
- RESult Subsystem 32
- :RESult:FORMat 33
- :RESult:FORMat:ESCape 33
- :RESult:RECycle:ALL 34
- :RESult:RECycle[:LATest] 34
- STANDby Subsystem 35
- SYSTem Subsystem 36
- WORKspace Subsystem 37
- :WORKspace[:SELected]:NAME? 38
- :WORKspace:STATe? 38
- Error Messages 39
- 7 Utilities 41
- System Requirements 43
- Desktop EasyEXPERT 44
- About Desktop EasyEXPERT 45
- To Install Desktop EasyEXPERT 46
- To Start Desktop EasyEXPERT 47
- Execution Mode dialog box 47
- Start EasyEXPERT window 48
- Using 4155B/4156B/4155C/4156C 50
- License Management Tool 53
- License Management Tool GUI 54
- Setup File Converter 55
- Setup File Converter GUI 56
- MDM File Converter 57
- MDM File Converter GUI 58
- Utility Programs 59
- SetupFileConverter.exe 60
- MdmFileConverter.exe 63
- Utilities 72
- 8 Application Library 77
- Application Test Definitions 79
- Application Library 81
- Accuracy 91
- Capacitance (F) 92
- Capa citance (F) 93
- HRSMU, ASU+SMU 94
- Measurement Accuracy 95
- Reading Accuracy (%) 102
- Offset Accuracy (F) 102
- 9 If You Have a Problem 127
- When You Operate B1500 129
- ASU is not Detected 130
- To Simplify the Connections 131
- When You Perform Measurement 132
- )HUULWHEHDGV 134
- 7HVWGHYLFH 134
- Measurement 136
- To Make Backup 138
- To Check Module Slots 138
- To Check ASU/SMU Combination 138
- Data Backup and Recovery 140
- Folders to Backup 141
- To Make Database Backup 141
- To Restore Database Backup 142
- To Make Backup of Other Data 143
- B1500 System Recovery 144
- To Initialize Database 146
- To Restore Database 147
- Updating EasyEXPERT 148
- If You Have a Problem 150
- 10 Error Message 151
- Agilent FLEX Execution Error 182
- DAC test 209
- 3465 IM short test failed 213
- *B1540-90020* 228
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies EasyEXPERT
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.143 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels