Agilent Technologies N5230C Guide de l'utilisateur télécharger pdf (Page 58)

52 User’s Guide

U3025AE10 Operational Check

Operational Check Procedure for E8363/4C and N5230C Systems

1. Connect the ECal or the mechanical cal kit to Port 1 or the port you are testing. Torque

to 8 in-lb. For more information press the Help button, see Figure 50.

2. Perform a 1-Port Calibration on Port 1. On the PNA, press Response > CAL > Start Cal

> Calibration Wizard.

a. If using a mechanical cal kit, select SmartCal.

b. If using an ECal module, select ECal.

3. Continue following the Cal Wizard prompts. In the “Select Calibration Ports and ECal

Module” window, press Clear All and select Port 1, then press Next.

Figure 50 1-Port Calibration

4. Continue to follow the prompts until the “Calibration Completed” window appears.

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 71 72

Agilent Technologies 1
U3025AE10 1
Warranty Statement 2
Safety Notes 3
Statement of Compliance 3
Definitions 3
Contents 5
Description 9
Network Analyzer Requirement 10
Available Options 11
Verifying the Shipment 12
General Specifications 13
Environmental Requirements 14
Table 4 System Dimensions 15
0.01w 0.98w+ 0.99w= 16
50⁄Ω0.98w= 16
Front and Rear Panel Features 18
14 User’s Guide 20
Locking Feet 21
(5023-0132) 21
Included in package 21
Screws (0515-1619) 21
16 User’s Guide 22
12-Port RF Cable Connections 23
18 User’s Guide 24
User’s Guide 19 25
Installing New Firmware 26
User’s Guide 21 27
22 User’s Guide 28
User’s Guide 23 29
24 User’s Guide 30
User’s Guide 25 31
Figure 21 Receiver Ports 32
User’s Guide 27 33
28 User’s Guide 34
User’s Guide 29 35
30 User’s Guide 36
User’s Guide 31 37
Control Lines 38
User’s Guide 33 39
Scroll Bar 40
User’s Guide 35 41
36 User’s Guide 42
User’s Guide 37 43
DUT Control Lines 44
40 User’s Guide 46
U3025AE10 DUT Control Lines 46
User’s Guide 41 47
U3025AE10 DUT Control Lines 47
Operational Check 49
Equipment Required 50
User’s Guide 45 51
U3025AE10 Operational Check 51
46 User’s Guide 52
U3025AE10 Operational Check 52
1-Port Calibration Procedure 53
48 User’s Guide 54
Error Terms 55
Enable 55
50 User’s Guide 56
User’s Guide 51 57
52 User’s Guide 58
User’s Guide 53 59
54 User’s Guide 60
User’s Guide 55 61
56 User’s Guide 62
Theory of Operation 63
System Block Diagrams 64
Service Information 65
Introduction 66
Before Applying Power 66
Connector Care and Cleaning 66
Shipping Instructions 66
Declaration of Conformity 66
EMC Information 67
Safety Information 67
Warnings 68
Cautions 69
ICES/NMB-001 70
Contacting Agilent 71
66 User’s Guide 72
U3025AE10 Contacting Agilent 72

Commentaires sur ces manuels

Pas de commentaire

Agilent Technologies N5230C Guide de l'utilisateur Page 58

Commentaires sur ces manuels

Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies N5230C