Agilent-technologies E1300B Manuel d'utilisateur Page 134
- Page / 244
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
:BOOT:COLD DIAGnostic:BOOT:COLD causes the System Instrument to restart (re-boot).
Configurations stored in non-volatile memory and RS-232 configurations are
reset to their default states:
• DRAM, NRAM, and RDISk memory segments are cleared
• Serial Interface parameters set to:
– BAUD 9600
– BITS 8
– PARity NONE
– SBITs 1
– DTR ON
– RTS ON
– PACE XON
• Serial 0 Owner = system
NOTE Resetting the serial interface parameters takes about 0.01 seconds for the
built-in serial port and 0.75 seconds per serial plug-in card. While this is taking
place the System Instrument will still respond to serial polls. If you are using a
serial poll to determine when the cold boot cycle is complete, you should insert a
delay of 1 second per plug-in serial card (E1324) before polling the system
instrument. This will prevent incorrectly determining that the system instrument
has completed its boot cycle.
Comments • The System Instrument goes through its power-up self tests.
• Related Commands: DIAG:BOOT:WARM
Example Re-booting the System Instrument (cold)
DIAG:BOOT:COLD force boot
DIAGnostic:BOOT:COLD
7-6 System Instrument Command Reference
- 75000 SERIES B 1
- Mainframes 1
- E1300B and E1301B 1
- Multimeter User’s Manual 6
- About this Manual 8
- Table of Contents 9
- 6 - Table of Contents 14
- Getting Started 15
- Instrument 17
- Definition 17
- Introductory 18
- Programming 18
- Examples 18
- 1-6 Getting Started 20
- Using the Front Panel 21
- A 60-Second Menu 22
- Tutorial 22
- Using the System 23
- Instrument Menu 23
- How to Reset the System 24
- Using the Other 25
- Instrument Menus 25
- How to Open/Close Channels 26
- How to Scan Channels 26
- How to Select Monitor Mode 27
- Executing 29
- Menu Keys 30
- Display Control & 30
- Editing Keys 30
- Instrument Control 31
- Other Keys 31
- In Case of Difficulty 32
- System Instrument Menu 34
- Switchbox Menu 36
- Using the Front Panel 2-17 37
- Scanning Voltmeter Menu 38
- Using the Front Panel 2-23 43
- Counter Menu 46
- 2-28 Using the Front Panel 48
- Chapter 3 49
- Terminal Interface 50
- Features 50
- General Key 62
- Descriptions 62
- Using Supported 64
- Terminals 64
- Using Other 67
- What “Not Supported” 68
- Testing Terminals for 68
- Compatibility 68
- Using a Terminal 69
- Without Menus 69
- Using the Mainframe 89
- Mainframe Data 94
- Non-Volatile User 95
- Downloading Device Drivers 99
- GPIB bus 100
- Configuration 101
- Download Program 102
- Downloading 104
- Drivers in MS-DOS 104
- Systems with 105
- Drivers in GPIB 105
- Systems with BASIC 106
- Multiple Drivers 107
- Checking Driver 107
- Manually 108
- Downloading a 108
- Driverdown manual 108
- Manually Downloading 109
- Over GPIB 109
- Over RS-232 109
- Chapter 6 115
- Status System 116
- Structure 116
- The Status Byte 117
- Register 117
- Reading the Status 118
- Byte Register 118
- Standard Event Status 120
- Unmasking Standard 120
- Event Status Bits 120
- Reading the 122
- Condition Register 122
- Unmasking the 122
- Operation Event 122
- Register Bits 122
- Clearing the Operation 123
- Event Register Bits 123
- Using the Operation 123
- Status Group Registers 123
- Interrupting an 124
- External Computer 124
- Synchronizing an 126
- Chapter 7 129
- SCPI Command 132
- Reference 132
- :COMMunicate 135
- :SERial[0][:OWNer] 135
- :SERial[0][:OWNer]? 136
- :SERial[n]:STORe 136
- :DOWNload:CHECked 137
- [:MADDress] 137
- :SADDress 139
- :DOWNload 141
- :DRIVer:LOAD 145
- < driver_block> 145
- :DRIVer :LOAD: 145
- :OPERation 160
- :CONDition? 160
- :OPERation:ENABle 160
- <event> 160
- :SERial[n] :CONTrol 165
- :CONFigure 182
- :DLADdress? 182
- ADDR 0" 184
- :HIERarchy? 185
- :HIERarchy:ALL? 186
- :INFormation? 186
- GPIB Message 200
- Device Clear (DCL) or 201
- Selected Device Clear 201
- Command Quick 203
- SCPI Commands Quick Reference 204
- Command Description 204
- System Instrument 204
- Specifications 209
- SCPI Conformance 211
- Information 211
- A-4 Specifications 212
- Specifications A-5 213
- A-6 Specifications 214
- Specifications A-7 215
- D/A Converter 216
- Commands 216
- Specifications A-9 217
- Specifications A-11 219
- A-12 Specifications 220
- Error Messages 221
- Error Messages B-3 223
- Error Messages and Causes 223
- Code Message Cause 223
- B-4 Error Messages 224
- Start-up Error 225
- Messages 225
- B-6 Error Messages 226
- Connecting and Configuring a 227
- Display Terminal 227
- Agilent 24542H 228
- Configuring a 229
- Terminal for the 229
- Mainframe 229
- Configuring the 230
- Mainframe with 230
- Appendix D 233
- Sending Binary 234
- Data Over RS-232 234
Produits connexes et manuels pour Matériel Agilent-technologies E1300B
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels