Agilent Technologies N9360A Manuel d'utilisateur Page 41
- Page / 376
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Operating Procedures 4
N9360A Multi UE Tester W-CDMA User Manual 4-3
Test Preparat io n
The following procedures are require before proceeding with
any test:
System Requirements
• The following equipment are required to setup the test
system:
• The Agilent N9360A Multi UE Tester.
• An RF cable, RF antenna coupler (type N9360A-A02) or
shield case (part number type N9360A-S01) to connect RF
signals to the mobile phone under test.
• A printer and a printer cable if required.
Figure 4-2 Typi c al Te st S et u p
CAUTION
Make sure that the input signal level does not exceed the maximum
level allowed. Otherwise, Tester failure may occur.
- Agilent N9360A 1
- Multi UE Tester 1
- Notation 3
- Trademarks 4
- Additional Information: 6
- Performance Criteria: 6
- Contents 7
- List of Figures 13
- 5 Screen Reference 5-1 14
- 6 Troubleshooting 6-1 17
- List of Tables 19
- Legal Information 23
- Service And Support 25
- 1 Legal Information 26
- Agilent Technologies 27
- Safety Information 28
- When Operating The Tester 29
- Overview 31
- Functions 32
- Reference Sensitivity Level 33
- Features 34
- 3 Overview 36
- Accessories 37
- Operating Procedures 39
- Test Flow 40
- Test Preparat io n 41
- Installing The Test USIM 42
- Connections 42
- Connecting a Printer 43
- USB Memory Device 44
- Test Procedure 45
- Storing Numeric Values 48
- Recalling Numeric Values 50
- System Selection 52
- Figure 4-13 [Initial] Screen 55
- RF IN/OUT Loss Correction 57
- Sequence] Screen 61
- Downlink TX Power 63
- 6 Set the test condition 67
- Refer to “Saving Test Setup 83
- File" on page 5-171 83
- Handover 84
- 8 Set the input fields 87
- Refer to “Saving Test 91
- Emergency Call 92
- 6 Start Manual Test 99
- 4 Operating Procedures 100
- Set the input fields 101
- Operating Procedures 4 103
- Algorithm" 107
- 5 Set the Band fields 113
- Ending A Test 115
- Screen Reference 117
- Screen Flow Chart 118
- Top Menu Screen 119
- 5 Screen Reference 120
- Softkey Menu Field 121
- Softkey Menu 1 121
- Softkey Menu 2 121
- Screen Field 122
- Message Field 122
- Configuration Screen 123
- Softkey Menu 124
- Option Installation/Backup 127
- Option Backup 128
- Firmware Update Screen 129
- Softkey Menu 3 131
- Update Flash Screen 133
- Network Setting Screen 136
- Initial Screen 140
- Return to Menu Screen 143
- PRESET Select Mode Screen 144
- Automatic Test 146
- RF Test in Automatic Test 147
- TEST USIM 148
- Stand-by Screen 149
- Measuring Screen 155
- Measuring Talk Screen 159
- Abort Screen 163
- Explanation 166
- Sequence 2 Screen 167
- Measurement Result Screen 169
- Input Field (continued) 173
- Manual Test 175
- RF Test in Manual Test 176
- Softkey Menu 4 179
- Location Update Screen 183
- Softkey Field 184
- Connection Screen 188
- Screen Reference 5 189
- CPICH RSCP Screen 197
- SMS Screen 206
- HSDPA Screen 213
- HSDPA Measuring Screen 231
- TX Analyzer 242
- Screen Fields 246
- Signal Generator 256
- Configuration 261
- Softkey Menu-3 263
- W-CDMA Mode is set to HSDPA 278
- Saving Test Setup File 287
- Softkey Menu 1 S 290
- Recalling Test Setup File 292
- Deleting Test Setup File 296
- Troubleshooting 311
- Item To Be Checked 312
- Table 6-1 Item To Be Checked 313
- Error Information 314
- Error Codes for Error Screens 315
- 6 Troubleshooting 316
- Measurement Performance 318
- Frequency Error 319
- Error Vector Magnitude (EVM) 319
- Origin Offset 320
- Sensitivity/BER 320
- ACLR DSB 5MHz (W07 Option) 320
- ACLR DSB 10MHz (W07 Option) 321
- OBW (W07 Option) 321
- Choices or Ranges 323
- –99.99 to 0.00 330
- W-CDMA (FDD) System 333
- Frequency Bands 334
- TX-RX Frequency Separation 334
- Channel Number 335
- UE Maximum Output Power 336
- List of Abbreviations 337
- Introduction 342
- Specifications 342
- Operating the Antenna Coupler 343
- Channels 345
- Modulation is set to Idle 346
- Spreading code (non-HSDPA) 347
- Spreading code (HSDPA) 348
- DL reference channel (HSDPA) 351
- OCNS (non-HSDPA) 354
- OCNS Signal 355
- OCNS (HSDPA) 356
- Performance Test 359
- Open Loop Power 360
- Maximum Output Power 362
- Error Vector Magnitude 363
- Inner Loop Power 367
- Reference Sensitivity 371
- ACLR DSB 373
- Minimum TX Power 375
Produits connexes et manuels pour Mise en réseau Agilent Technologies N9360A
(262 pages)
(21 pages)
(47 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels