Agilent Technologies 222A Manuel d'instructions Page 72
- Page / 123
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
72
Programming Reference
SCPI Instrument Command List
Command :VOLT[1]:HIGH
Long
[:SOURce]:VOLTage[1][:LEVel][:IMMediate]:HIGH
Form Set & Query
Parameter Numeric
Parameter suffix
V
with engineering prefixes.
Value coupling
Range coupling With low level, see page 73
*RST value 500 mV
Specified limits –9.9 V to 10.0 V (50
Ω
into 50
Ω
)
Description Use this command to program the high level voltage of the OUTPUT
signal. Note that to set the OUTPUT levels in terms of voltage, you first
have to execute the
[:SOURce]:HOLD VOLTage
command to enable the
[:SOURce]:VOLTage
subsystem.
The available voltage range is limited by the combination of:
• Specified current limits
• Actual OUTPUT impedance setting
:OUTPut:IMPedance
• Actual expected load impedance setting
:OUTPut:IMPedance:EXTernal
Example To set the high level voltage:
Amplitude = High – Low
Offset =
High – Low
2
:HOLD VOLT
:VOLT:HIGH 4.8V
Enable VOLTAGE subsystem
Set OUTPUT high level voltage to 4.8 V
- Reference Guide 1
- Agilent 81101A 50 MHz 3
- Pulse Generator 3
- Copyright 4
- Warranty 4
- Limitation of Warranty 5
- Exclusive Remedies 5
- Certification 5
- Services and Support 5
- Safety Summary 6
- Ground the Instrument 7
- Safety Symbols 8
- About this Book 9
- Conventions Used in this Book 10
- Contents 11
- 1General Programming 13
- The GP-IB Interface Bus 14
- Agilent 81101A Remote Control 15
- Programming Recommendations 16
- Common Command Summary 18
- Status Model 19
- Condition Register 20
- Transition Filters 20
- Event Register 20
- Enable Register 21
- Status Byte 22
- Standard Event Status Group 22
- OPERation Status Group 23
- QUEStionable Status Group 24
- 2Programming Reference 25
- Agilent 81101A SCPI Command 26
- Programming Reference 31
- Programming the Instrument 35
- Continuous 36
- Triggered 36
- External Width 37
- SCPI Instrument Command List 38
- :DISPlay[:WINDow][:STATe] 43
- DISP OFF 43
- :MMEMory:CATalog? 44
- :MMEMory:CDIRectory 44
- :MMEMory:COPY 45
- :MMEMory:DELete 45
- :MMEMory:INITialize 45
- :MMEMory:LOAD:STATe 46
- :MMEMory:STORe:STATe 46
- :OUTPut[1][:NORMal][:STATe] 47
- :OUTP ON 47
- :OUTPut[1]:IMPedance:EXTernal 47
- :OUTPut[1]:POLarity 48
- Amplitude = High – Low 50
- Offset = 50
- High – Low 50
- Period = 54
- Frequency 54
- [:SOURce]:HOLD 55
- [:SOURce]:PHASe[1][:ADJust] 56
- [:SOURce]:PULSe:DCYCle[1] 57
- [:SOURce]:PULSe:DELay[1] 57
- [:SOURce]:PULSe:DELay[1]:HOLD 58
- [:SOURce]:PULSe:DELay[1]:UNIT 59
- DblDel% = 60
- Frequency = 62
- [:SOURce]:PULSe:PERiod:AUTO 63
- [:SOURce]:PULSe:TDELay[1] 63
- [:AMPlitude] 67
- [:SOURce]:PULSe:WIDTh[1] 68
- [:SOURce]:ROSCillator:SOURce 68
- Amplitude 70
- Offset = 72
- High–Low 73
- :STATus:PRESet 76
- :SYSTem:CHECk[:ALL][:STATe] 78
- :SYSTem:ERRor? 78
- :SYSTem:KEY 79
- :SYSTem:PRESet 81
- :SYSTem:SECurity[:STATe] 82
- :SYSTem:SET 83
- :SYSTem:VERSion? 83
- :SYSTem:WARNing[:COUNt]? 83
- :SYSTem:WARNing:STRing? 84
- :SYSTem:WARNing:BUFFer? 84
- :TRIGger[:SEQuence[1]]:COUNt 84
- :TRIGger:IMPedance 85
- :TRIGger:LEVel 86
- :TRIGger:SLOPe 86
- 3Specifications 89
- Manufacturer 90
- Supplementary 90
- Information 90
- Agilent 81101A Specifications 91
- Recalibration period 92
- Acoustic Noise Emission 92
- Timing Specifications 93
- Transition Times 95
- Level Specifications 96
- Clock Sources 97
- Clock / PLL Reference Input 98
- Phase Locked Loop (PLL) 98
- Output Modes 99
- Trigger Modes 100
- Trigger Output 101
- Strobe Output 101
- Typical Delays 102
- Human Interface 103
- Remote Control 104
- Pulse Parameter Definitions 105
- Time Reference Point 106
- Pulse Period 106
- Trigger Delay 106
- Pulse Width 106
- Pulse Delay 107
- Double Pulse Delay 107
- Interchannel Delay (Skew) 107
- Transition Time 108
- Linearity 108
- Stability 109
- Pulse Levels 109
- Preshoot, Overshoot, Ringing 110
- Settling Time 110
- Repeatability 111
- Specifications 112
- Front Panel Controls 117
- Edition E0300 118
- Printed in Germany 118
- 81101-91021 118
- DECLARATION OF CONFORMITY 123
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies 222A
(24 pages)
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels