Agilent Technologies 53150A Manuel d'instructions Page 84
- Page / 174
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 3 Programming Your Counter for Remote Operation
Programming the Counter to Synchronize Measurements
3-48 Programming Guide
3
Programming the Counter to
Synchronize Measurements
Synchronizing Measurement Completion
There are three commands for synchronizing the end of a measurement
and computer transfer of data:
1. The *WAI command
2. The *OPC? command
3. The *OPC command to assert SRQ
The following discussion shows how to use these three commands.
Resetting the Counter and Clearing the Interface
Before attempting any programming, it is best to set the Counter to a
known state. The following command grouping illustrates how to reset the
Counter. Before issuing these commands, execute a device clear to reset
the interface and the Counter. You should consult your interface card’s
documentation for information on issuing a device clear, since the device
clear command is specific to the interface you are using. Perform the
following steps:
1. Issue an Interface Clear and a Device Clear. (See your computer or
interface card documentation for information on how to issue this
command.)
2. Issue the following commands:
*RST
*CLS
*SRE 0
*ESE 0
:STAT:PRES
- Programming Guide 1
- Contents 3
- 4 Command Reference 5
- 5 Errors 6
- Before You Start 7
- Getting Started 9
- How to Use This Guide 9
- New Users 10
- Experienced Programmers 11
- Applications 11
- Programming Guide Contents 12
- Assumptions 13
- Related Documentation 14
- 1-10 Programming Guide 16
- Command Summary 17
- Chapter 2 Command Summary 20
- 2-4 Programming Guide 20
- (Part 1 of 2) 20
- 2-6 Programming Guide 22
- SCPI Conformance Information 24
- IEEE 488.2 Common Commands 25
- 2-10 Programming Guide 26
- Programming Guide 2-11 27
- Std/New Column 28
- Parameter Form Column 28
- Programming Guide 2-13 29
- 2-14 Programming Guide 30
- Programming Guide 2-15 31
- 2-16 Programming Guide 32
- Programming Guide 2-17 33
- 2-18 Programming Guide 34
- *RST Response 35
- 2-20 Programming Guide 36
- Programming Your Counter 37
- Chapter Summary 39
- Programming Examples 40
- To Connect With the GPIB 41
- Making an RS-232 Cable 43
- (Female) 44
- Remote/Local Operation 47
- Common Command Format 48
- SCPI Command and Query Format 48
- Elements of SCPI Commands 49
- Abbreviated Commands 50
- Keyword Separator 50
- Optional Keyword 50
- :SENS:FREQ:RES 51
- :FREQ:RES 51
- Parameter Types 52
- Parameter Separator 53
- Query Parameters 53
- Suffixes 53
- Command Terminator 54
- Using Multiple Commands 55
- :SENS:AVER:COUN 5 56
- :SENS:AVER:STAT ON 56
- Response Messages 57
- Response Message Syntax 57
- <new line> 58
- Response Message Data Types 59
- 3-24 Programming Guide 60
- Status Reporting 61
- 3-26 Programming Guide 62
- Status Byte Register and 63
- RQS /MSS 63
- Condition Register 70
- Transition Filter 70
- Event Register 71
- Event Enable Register 72
- Programming the Counter for 77
- Event Status Register 78
- Computer When Measuring has 79
- Completed—Example 3 79
- 3-44 Programming Guide 80
- Programming Guide 3-45 81
- FREQ:OFFS:STAT ON 83
- Programming the Counter to 84
- Synchronize Measurements 84
- Using the *WAI Command 85
- Using the *OPC? Command 85
- Writing SCPI Programs 88
- Programming Guide 3-53 89
- 3-56 Programming Guide 92
- Programming Guide 3-57 93
- 3-58 Programming Guide 94
- Programming Guide 3-59 95
- 3-60 Programming Guide 96
- Command Reference 97
- COMMAND :ABORt 100
- FRONT-PANEL 100
- :DISPlay Subsystem 101
- COMMAND GET 103
- COMMENTS • *RST: OFF 104
- :INPut Subsystem 105
- :MEASure Subsystem 106
- Command Description 107
- COMMAND :CONFigure? 108
- FUNCTION 112
- DESCRIPTION 112
- Using :MEAsure 114
- Using :CONFigure with :READ? 115
- :MEMory Subsystem 116
- [:SENSe] Subsystem 118
- [:SENSe]:FUNCtion Subtree 123
- [:SENSe]:POWer Subtree 125
- [:SENSe]:ROSCillator Subtree 126
- :STATus Subsystem 127
- COMMAND :STATus:PRESet 131
- :STATus:QUEStionable Subtree 132
- :SYSTem Subsystem 135
- :TRIGger Subsystem 138
- COMMAND *CLS 139
- *DDT <arbitrary block> 140
- (Define Device Trigger Query) 140
- COMMAND *ESR? 143
- *IDN? (Identification Query) 144
- *IST? (Instrument Status) 144
- *RCL (Recall Command) 146
- COMMAND *RST 147
- *SAV (Save Command) 148
- <NRF> RANGE • 0 to 255 149
- <NRF> RESOLUTION 1 149
- COMMAND *STB? 151
- COMMAND *TRG 152
- *TST? (Self-Test Query) 153
- Introduction 156
- Reading an Error 156
- Error Queue 157
- Error Types 158
- Command Error 159
- Execution Error 159
- Query Error 160
- Error List 160
- Chapter 5 Errors 161
- Programming Guide 5-7 161
- Table 5-2. Errors 161
- 5-8 Programming Guide 162
- Table 5-2. Errors (Continued) 162
- Programming Guide 5-9 163
- 5-10 Programming Guide 164
- Programming Guide Index-1 165
- Index-2 Programming Guide 166
- Programming Guide Index-3 167
- Index-4 Programming Guide 168
- Programming Guide Index-5 169
- Index-6 Programming Guide 170
- Programming Guide Index-7 171
- Index-8 Programming Guide 172
- 1-800-800-5281 173
Produits connexes et manuels pour Multimètres Agilent Technologies 53150A
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels