Agilent Technologies E8462A Manuel d'utilisateur Page 135
- Page / 156
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Register-Based Programming 133
Register Descriptions
The Multiplexer has 25 registers (refer to Table B-1). This section contains
a description of each register. Undefined register bits appear as "1" when the
register is read, and have no effect when written to.
You can write to the writable (W) registers and read from the readable (R)
registers which are listed in Table B-1.
Table B-1. Agilent E8462A 256-Channel Multiplexer Registers
Register Addr. Offset R/W Register Description (Register Address)
ID Register 00
h
R MFG ID Register (Base + 00
h
)
Device Type Register 02
h
R Device Type Register (Base + 02
h
)
Status/Control Register 04
h
R/W Status/Control Register (Base + 04
h
)
Relay Control Register 0 20
h
R/W Bank 0 Channels (CH 000 - 015, 032 - 047) (Base + 20
h
)
Relay Control Register 1 22
h
R/W Bank 1 Channels (CH 016 - 031, 048 - 063) (Base + 22
h
)
Relay Control Register 2 24
h
R/W Bank 2 Channels (CH 064 - 079, 096 - 111) (Base + 24
h
)
Relay Control Register 3 26
h
R/W Bank 3 Channels (CH 080 - 095, 112 - 127) (Base + 26
h
)
Relay Control Register 4 28
h
R/W Bank 4 Channels (CH 128 - 143, 160 - 175) (Base + 28
h
)
Relay Control Register 5 2A
h
R/W Bank 5 Channels (CH 144 - 159, 176 - 191) (Base + 2A
h
)
Relay Control Register 6 2C
h
R/W Bank 6 Channels (CH 192 - 207, 224 - 239) (Base + 2C
h
)
Relay Control Register 7 2E
h
R/W Bank 7 Channels (CH 208 - 223, 240 - 255) (Base + 2E
h
)
Tree Relay Control Register 0 30
h
R/W Tree Relays T1-T15 (CH 9000 - 9015) (Base + 30
h
)
Tree Relay Control Register 1 32
h
R/W Tree Relays T16-T21, C Relays C100-C108
(CH 9016 - 9021, 9100 - 9108) (Base + 32
h
)
Analog Bus Relay Control Register 34
h
R/W Analog Bus Relays AB200-AB204 (CH 9200 - 9204) (Base + 34
h
)
Timer Configuration Register 36
h
R/W Relay Settling Time (Base + 36
h
)
- *E8462-90000* 1
- Contents 3
- Certification 7
- Safety Symbols 8
- WARNINGS 8
- Documentation History 8
- Trademarks 8
- Declaration of Conformity 9
- Multiplexer 13
- Optional Terminal 14
- Warnings and Cautions 16
- Setting the Logical 17
- Setting the Interrupt 18
- Priority Line 18
- Protection 18
- Resistors 18
- Connecting Field Wiring 20
- Front Panel 21
- Connector Pin-Out 21
- 1-Wire Mode 22
- 2-Wire Mode 23
- 3-Wire Mode and 4-Wire Mode 24
- Connecting the 25
- Analog Bus 25
- Option 015 Ribbon Cable 27
- Connector Terminal 27
- Attaching a Terminal 30
- Block to the Multiplexer 30
- Programming the Multiplexer 31
- CARD NUMBER 01 32
- CARD NUMBER 02 32
- CARD NUMBER 03 32
- Channel Numbers 33
- Ranges, and Lists 33
- Initial Operation 34
- Example: Reset 35
- Self Test, Module 35
- ID, and Close 35
- Using the Multiplexer 37
- Switching or Scanning 38
- Performing 39
- Measurements via 39
- 1-Wire @ Ter0 40
- 2-Wire @ Ter0 and 41
- Other Modes 42
- Using the Multiplexer 41 43
- Mode: WIRE1x2 and 44
- Mode: WIRE1x4 45
- WIRE2x4 45
- Mode: WIRE1x8 46
- WIRE2x8 46
- Scanning Channels 47
- Synchronizing the 48
- Multiplexer with a 48
- Multimeter 48
- Using the Multiplexer 51 53
- BUS trigger (GET or *TRG) to 53
- Recalling and Saving States 54
- Detecting Error Conditions 55
- Function Mode Topologies 56
- WIRE1 Mode Topology 57
- WIRE2 Mode Topology 58
- WIRE3 and WIRE4 Mode Topology 59
- WIRE1X2 Mode Topology 60
- WIRE1X4 Mode Topology 61
- WIRE1X8 Mode Topology 62
- WIRE2X2 Mode Topology 63
- WIRE2X4 Mode Topology 64
- WIRE2X8 Mode Topology 65
- WIRE4X2 Mode Topology 66
- WIRE4X4 Mode Topology 67
- 66 Using the Multiplexer 68
- Command Reference 69
- Commands 70
- Variable Command 71
- SCPI Command Reference 72
- Subsystem Syntax ABORt 73
- ARM:COUNT 74
- 74
- ARM:COUNt? 74
- Parameters 75
- Example Query Number of Scans 75
- DIAGnostic 76
- DIAGnostic:INTerrupt:TIMer 78
- DIAGnostic:INTerrupt:TIMer? 78
- DIAGnostic:SCAN:DELay 79
- DIAGnostic:SCAN:DELay? 79
- DISPlay:MONitor:CARD 80
- DISPlay:MONitor:CARD? 80
- DISPlay:MONitor[:STATe] 81
- DISPlay:MONitor[:STATe]? 82
- INITiate 83
- INITiate:CONTinuous? 84
- INITiate[:IMMediate] 84
- OUTPut:ECLTrgn[:STATe] 85
- OUTPut:ECLTrgn[:STATe]? 86
- OUTPut[:EXTernal][:STATe] 86
- OUTPut[:EXTernal][:STATe]? 87
- OUTPut:TTLTrgn[:STATe] 87
- OUTPut:TTLTrgn[:STATe]? 88
- [ROUTe:] 89
- [ROUTe:]CLOSe? 92
- [ROUTe:]FUNCtion 92
- [ROUTe:]FUNCtion? 94
- [ROUTe:]OPEN 94
- [ROUTe:]OPEN? 97
- [ROUTe:]SCAN 98
- ROUT:FUNC command 99
- [ROUTe:]SCAN:MODE 100
- [ROUTe:]SCAN:MODE? 101
- [ROUTe:]SCAN:PORT 101
- [ROUTe:]SCAN:PORT? 102
- Subsystem Syntax STATus 103
- STATus:OPERation[:EVENt]? 105
- STATus:OPERation:CONDition? 105
- STATus:OPERation:ENABle 105
- STATus:OPERation:ENABle? 105
- STATus:PRESet 106
- SYSTem:CDEScription? 107
- SYSTem:CPON 108
- SYSTem:CTYPe? 108
- SYSTem:ERRor? 109
- TEST:NUMBer? 110
- TRIGger[:IMMediate] 112
- TRIGger:SLOPe 112
- TRIGger:SLOPe? 113
- TRIGger:SOURce 113
- TRIGger:SOURce? 115
- 488.2-1987 116
- SCPI Command Quick Reference 117
- Application Examples 119
- Reset Conditions 120
- The Scanning Voltmeter 121
- Making Measurements 122
- Select range 125
- Agilent E8462A Specifications 127
- Input Characteristics 128
- AC Performance 129
- (Typical) 129
- Register-Based Programming 131
- A16 Address Space 132
- Outside the Command 132
- Inside the Command 133
- Module or Mainframe 133
- Register Descriptions 135
- Device Type 136
- Register 136
- Status/Control 136
- • Set the SYSFAIL bit to “1” 137
- • Wait 10 nanoSeconds 137
- Relay Control 138
- Registers 138
- Timer Control 140
- Program Timing and Execution 141
- Using a Multimeter 142
- Programming Example 143
- Error Handling Function 145
- Error Messages 147
- 146 Error Messages 148
- Index 147 149
- 148 Index 150
- Index 149 151
- 150 Index 152
- Index 151 153
- 152 Index 154
- Index 153 155
- 154 Index 156
Produits connexes et manuels pour Multimètres Agilent Technologies E8462A
(16 pages)
(4 pages)
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels