Agilent Technologies E8257D/67D Guide d'installation

Agilent TechnologiesAgilent TechnologiesE8257D/67D and E8663D PSG Signal GeneratorsInstallation Guide

4 Chapter 2Getting Started PreliminaryMeeting Electrical and Environmental Requirements PreliminaryMeeting Electrical and Environmental RequirementsEn

Chapter 2 5Prelimniary Getting StartedPreliminary Configuring the DisplayConnecting the AC Power CordThis is a Safety Class 1 Product provided with a

6 Chapter 2Getting Started PreliminaryConfiguring the Display PreliminaryInverse VideoPress Utility > Display > Inverse Video Off On.This togg

Chapter 2 7Prelimniary Getting StartedPreliminary Configuring for Remote ControlConfiguring for Remote ControlGPIB Interface Configuration1. Press Ut

8 Chapter 2Getting Started PreliminaryConfiguring for Remote Control PreliminaryDHCP Configuration1. Press Utility > GPIB/RS-232 LAN > LAN Setup

Chapter 2 9Prelimniary Getting StartedPreliminary Ordering AccessoriesOrdering AccessoriesThe following accessories can be ordered when a signal gener

10 Chapter 2Getting Started PreliminaryProper Usage and Cleaning PreliminaryProper Usage and CleaningThe signal generator cover protects against physi

Chapter 2 11Prelimniary Getting StartedPreliminary Contacting Agilent Sales and Service OfficesContacting Agilent Sales and Service OfficesAssistance

12 Chapter 2Getting Started PreliminaryReturning a Signal Generator to Agilent Technologies Preliminary

Chapter 3 133 Operation VerificationNOTE For the instrument to meet performance specifications allow a warm up period of 45 minutes within an operatio

Notices© Agilent Technologies, Inc. 2006-2009No part of this manual may be reproduced in any form or by any means (including elec-tronic storage and r

14 Chapter 3Operation VerificationChecking the Maximum Leveled Power• The current status of the self-test is: Incomplete. Not all tests have been run

Chapter 3 15Operation VerificationChecking the Maximum Leveled Power10. Press Return > Sweep > Freq. The SWEEP annunciator is now on and a cont

16 Chapter 3Operation VerificationChecking the Maximum Leveled PowerTable 3-1 Frequency and Power Level Limits (For PSGs with s/n prefixes <US4928/

Chapter 3 17Operation VerificationChecking the Maximum Leveled PowerTable 3-2 Frequency and Power Level Limits (For PSGs with s/n prefixes >=US4928

18 Chapter 3Operation VerificationChecking the Output PowerMaximum Leveled Power Check FailureIf a maximum leveled power check fails, perform the foll

Chapter 3 19Operation VerificationChecking the Output Power✔✔✔✔Power Sensor,Input: 2.4 mm (m)Agilent 8487A Option H84 power sensor (Option H84 adds a

20 Chapter 3Operation VerificationChecking the Output PowerPerform the following procedure to check the signal generator output power:1. Zero and cali

Chapter 3 21Operation VerificationChecking the Output Power2. Connect the equipment as shown:3. Press Preset.4. Press RF On/Off. The RF On annunciato

22 Chapter 3Operation VerificationChecking the Output PowerTable 3-5 Frequency and Power Level Limits (For PSGs with s/n prefixes <US4928/MY4928)In

Chapter 3 23Operation VerificationChecking the Output PowerTable 3-6 Frequency and Power Level Limits (For PSGs with s/n prefixes >US4928/MY4928)In

Contentsiii1. Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24 Chapter 3Operation VerificationChecking the Output PowerNOTE Limit values are due to power measurement uncertainty.Problems with Output PowerIf a p

Chapter 4 254 Regulatory InformationStatement of ComplianceThis product has been designed and tested in accordance with IEC Publication 61010, Safety

26 Chapter 4Regulatory InformationDeclaration of ConformityDeclaration of ConformityA copy of the Manufacturer’s EU Declaration of Conformity for this

Index 27IndexAAC power cord 5AC symbol 1accessories 9address, GPIBaltitude requirements 4assistance 25Australian Communications Authority (C-tick) mar

Index28IndexTtemperature requirements 4troubleshootingmaximum leveled power 14output power 18self-test 13Vventilation requirements 4verification, oper

Contents iv4. Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

vDocumentation OverviewInstallation Guide• Safety Information• Getting Started• Operation Verification• Regulatory InformationUser’s Guide• Signal Gen

viService Guide• Troubleshooting• Replaceable Parts• Assembly Replacement• Post- Repair Procedures• Safety and Regulatory InformationKey Reference• Ke

Chapter 1 11 Safety InformationInstrument MarkingsThe following markings are used on the signal generator. Familiarize yourself with each marking and

2 Chapter 1Safety InformationWarnings, Cautions, and NotesWarnings, Cautions, and NotesThe following safety notations are used throughout this manual.

Chapter 2 32 Getting StartedChecking the Shipment1. Inspect the shipping container for damage.Signs of damage may include a dented or torn shipping co