Agilent-technologies System DC N5700 Manuel d'utilisateur Page 15
- Page / 132
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Series N5700 User’s Guide 15
2
Installation
General Information.......................................................................................... 16
Inspecting the Unit ...........................................................................................17
Installing the Unit.............................................................................................. 17
Connecting the Line Cord ................................................................................19
Connecting the Load.........................................................................................21
Output Voltage Sensing...................................................................................24
Load Considerations......................................................................................... 26
Parallel Connections......................................................................................... 28
Series Connections........................................................................................... 30
J1 Connector Connections.............................................................................. 32
This chapter describes how to install your power supply. It discusses
installation, rack mounting, and line cord connections.
This chapter also discusses how to connect your load to the output
terminals. It discusses what you need to know about wire sizes and
how to compensate for voltage drops in the load leads. It also
discusses various loads configurations and how to connect units in
series and parallel.
Before getting started, check the list under “Items Supplied” and
verify that you have received these items with your instrument. If
anything is missing, please contact your nearest Agilent Sales and
Service Office.
- 1
- Legal Notices 2
- Safety Notices 3
- In this Book 4
- Contents 5
- Quick Reference 7
- Output Features 8
- System Features 8
- Programmable Functions 9
- Model Ratings 9
- DC AMPS 10
- DC VOLTS 10
- The Rear Panel – At a Glance 12
- J2 Sense Connector 13
- SW1 Setup Switch 13
- Installation 15
- General Information 16
- Inspecting the Unit 17
- Installing the Unit 17
- Rack Installation 18
- Cleaning 18
- Connecting the Line Cord 19
- Connecting the Load 21
- CAUTION 22
- Output Voltage Sensing 24
- Local Sensing 25
- Remote Sensing 25
- Load Considerations 26
- Inductive Loads 27
- Parallel Connections 28
- Setting up the Master Unit 29
- Series Connections 30
- J1 Connector Connections 32
- Turn-On Check-Out 34
- UVL Check 35
- Constant Current Check 35
- OCP Check 35
- Normal Operation 36
- Protection Functions 37
- Under-Voltage Limit 38
- Over-Current Protection 38
- Over-Temperature Protection 39
- Power-Fail Protection 39
- Front Panel Lock-Out 39
- Output On/Off Controls 40
- Enable/Disable Terminals 41
- Power Supply OK Signal 42
- CURRENT LIMIT 44
- PROGRAMMING 44
- OUTPUT VOLTAGE 44
- Connecting to the Interfaces 48
- USB Interface 49
- LAN Interface 49
- Connecting to a Site LAN 50
- LAN Communication 52
- Using Telnet 53
- Using Sockets 53
- Using the Setup Utility 56
- Message Unit 59
- Queries 60
- Common Commands 60
- Command Terminators 60
- Parameter Types 61
- SCPI Command Completion 62
- Language Reference 63
- SCPI Command Summary 64
- Calibration Commands 66
- Measure Commands 67
- Output Commands 68
- Source Commands 69
- Status Commands 71
- STATus:PRESet 72
- STATus:OPERation[:EVENt]? 72
- STATus:OPERation:CONDition? 72
- STATus:OPERation:ENABle? 72
- System Commands 77
- OUTP Off [SOUR:]VOLT:LIM 0 78
- Trigger Commands 79
- Programming Examples 81
- Output Programming Example 82
- Programming Examples 6 83
- Trigger Programming Example 84
- Appendix A 87
- Specifications 87
- Performance Specifications 88
- Supplemental Characteristics 89
- 482.8+/-1.0mm 91
- 433+/-1.0mm 91
- 507.0+/-1.0mm 91
- 422.8+/-1.0mm 91
- Appendix B 93
- Verification and Calibration 93
- Verification 94
- Measurement Techniques 95
- Constant Voltage Tests 96
- CV Source Effect 97
- CV Noise 97
- Transient Recovery Time 98
- Constant Current Tests 99
- CC Source Effect 100
- WARNING 101
- 60 V, from 1.25 A to 11.25 A 107
- 100 V, from 0.75 A to 6.75 A 109
- 200 V, from 0.25 A to 2.25 A 111
- Calibration 113
- Appendix C 115
- Service 115
- Types of Service Available 116
- Repackaging for Shipment 116
- Operating Checklist 116
- Service Appendix C 117
- Symptom Check Action 117
- Error Messages 118
- Appendix C Service 120
- Command Errors (continued) 120
- Appendix D 123
- Compatibility 123
- Differences – In General 124
- Appendix D Compatibility 126
- Command 126
- Manual Updates 131
Produits connexes et manuels pour Outils Agilent-technologies System DC N5700
(103 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels