Agilent-technologies System DC N5700 Manuel d'utilisateur Page 7
- Page / 132
- Table des matières
- MARQUE LIVRES
- 1
- Legal Notices 2
- Safety Notices 3
- In this Book 4
- Contents 5
- Quick Reference 7
- Output Features 8
- System Features 8
- Programmable Functions 9
- Model Ratings 9
- DC AMPS 10
- DC VOLTS 10
- The Rear Panel – At a Glance 12
- J2 Sense Connector 13
- SW1 Setup Switch 13
- Installation 15
- General Information 16
- Inspecting the Unit 17
- Installing the Unit 17
- Rack Installation 18
- Cleaning 18
- Connecting the Line Cord 19
- Connecting the Load 21
- CAUTION 22
- Output Voltage Sensing 24
- Local Sensing 25
- Remote Sensing 25
- Load Considerations 26
- Inductive Loads 27
- Parallel Connections 28
- Setting up the Master Unit 29
- Series Connections 30
- J1 Connector Connections 32
- Turn-On Check-Out 34
- UVL Check 35
- Constant Current Check 35
- OCP Check 35
- Normal Operation 36
- Protection Functions 37
- Under-Voltage Limit 38
- Over-Current Protection 38
- Over-Temperature Protection 39
- Power-Fail Protection 39
- Front Panel Lock-Out 39
- Output On/Off Controls 40
- Enable/Disable Terminals 41
- Power Supply OK Signal 42
- CURRENT LIMIT 44
- PROGRAMMING 44
- OUTPUT VOLTAGE 44
- Connecting to the Interfaces 48
- USB Interface 49
- LAN Interface 49
- Connecting to a Site LAN 50
- LAN Communication 52
- Using Telnet 53
- Using Sockets 53
- Using the Setup Utility 56
- Message Unit 59
- Queries 60
- Common Commands 60
- Command Terminators 60
- Parameter Types 61
- SCPI Command Completion 62
- Language Reference 63
- SCPI Command Summary 64
- Calibration Commands 66
- Measure Commands 67
- Output Commands 68
- Source Commands 69
- Status Commands 71
- STATus:PRESet 72
- STATus:OPERation[:EVENt]? 72
- STATus:OPERation:CONDition? 72
- STATus:OPERation:ENABle? 72
- System Commands 77
- OUTP Off [SOUR:]VOLT:LIM 0 78
- Trigger Commands 79
- Programming Examples 81
- Output Programming Example 82
- Programming Examples 6 83
- Trigger Programming Example 84
- Appendix A 87
- Specifications 87
- Performance Specifications 88
- Supplemental Characteristics 89
- 482.8+/-1.0mm 91
- 433+/-1.0mm 91
- 507.0+/-1.0mm 91
- 422.8+/-1.0mm 91
- Appendix B 93
- Verification and Calibration 93
- Verification 94
- Measurement Techniques 95
- Constant Voltage Tests 96
- CV Source Effect 97
- CV Noise 97
- Transient Recovery Time 98
- Constant Current Tests 99
- CC Source Effect 100
- WARNING 101
- 60 V, from 1.25 A to 11.25 A 107
- 100 V, from 0.75 A to 6.75 A 109
- 200 V, from 0.25 A to 2.25 A 111
- Calibration 113
- Appendix C 115
- Service 115
- Types of Service Available 116
- Repackaging for Shipment 116
- Operating Checklist 116
- Service Appendix C 117
- Symptom Check Action 117
- Error Messages 118
- Appendix C Service 120
- Command Errors (continued) 120
- Appendix D 123
- Compatibility 123
- Differences – In General 124
- Appendix D Compatibility 126
- Command 126
- Manual Updates 131
Produits connexes et manuels pour Outils Agilent-technologies System DC N5700
(103 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels