Agilent Technologies 222A Manuel d'instructions Page 68
- Page / 123
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
68
Programming Reference
SCPI Instrument Command List
Command :PULS:WIDT[1]
Long
[:SOURce]:PULSe:WIDTh[1]
Form Set & Query
Parameter Numeric
Parameter suffix
S
with engineering prefixes
*RST value 100 ns
Specified limits 10 ns to 999.5 s (max. period –10 ns)
Description Use this command to program the width of the pulse signal. If you want
to set width as duty cycle use
[:SOURce]:PULSe:DCYCle[1]
.
If you want the pulse width to remain constant when the pulse period is
varied (rather than the duty cycle) use
[:SOURce]:PULSe:HOLD[1] WIDTh
.
Example To set and hold the pulse width:
Command :ROSC:SOUR
Long
[:SOURce]:ROSCillator:SOURce
Form Set & Query
Parameter
INTernal | EXTernal
*RST value
INT
Description Use this command to set/read the reference source for the PLL. If you
select the external reference (CLK-IN connector), you can choose to use
a 5 MHz or 10 MHz reference signal using
:ROSC:EXT:FREQ
.
:PULS:WIDT 50NS
:PULS:HOLD WIDTH
Set OUTPUT pulse width to 50 ns
Hold pulse width constant with varying period
INTernal
Lock the PLL to its internal reference
EXTernal
Lock the PLL to a reference signal at the
CLK-IN connector. The external refer-
ence signal can be 5 or 10 MHz.
- Reference Guide 1
- Agilent 81101A 50 MHz 3
- Pulse Generator 3
- Copyright 4
- Warranty 4
- Limitation of Warranty 5
- Exclusive Remedies 5
- Certification 5
- Services and Support 5
- Safety Summary 6
- Ground the Instrument 7
- Safety Symbols 8
- About this Book 9
- Conventions Used in this Book 10
- Contents 11
- 1General Programming 13
- The GP-IB Interface Bus 14
- Agilent 81101A Remote Control 15
- Programming Recommendations 16
- Common Command Summary 18
- Status Model 19
- Condition Register 20
- Transition Filters 20
- Event Register 20
- Enable Register 21
- Status Byte 22
- Standard Event Status Group 22
- OPERation Status Group 23
- QUEStionable Status Group 24
- 2Programming Reference 25
- Agilent 81101A SCPI Command 26
- Programming Reference 31
- Programming the Instrument 35
- Continuous 36
- Triggered 36
- External Width 37
- SCPI Instrument Command List 38
- :DISPlay[:WINDow][:STATe] 43
- DISP OFF 43
- :MMEMory:CATalog? 44
- :MMEMory:CDIRectory 44
- :MMEMory:COPY 45
- :MMEMory:DELete 45
- :MMEMory:INITialize 45
- :MMEMory:LOAD:STATe 46
- :MMEMory:STORe:STATe 46
- :OUTPut[1][:NORMal][:STATe] 47
- :OUTP ON 47
- :OUTPut[1]:IMPedance:EXTernal 47
- :OUTPut[1]:POLarity 48
- Amplitude = High – Low 50
- Offset = 50
- High – Low 50
- Period = 54
- Frequency 54
- [:SOURce]:HOLD 55
- [:SOURce]:PHASe[1][:ADJust] 56
- [:SOURce]:PULSe:DCYCle[1] 57
- [:SOURce]:PULSe:DELay[1] 57
- [:SOURce]:PULSe:DELay[1]:HOLD 58
- [:SOURce]:PULSe:DELay[1]:UNIT 59
- DblDel% = 60
- Frequency = 62
- [:SOURce]:PULSe:PERiod:AUTO 63
- [:SOURce]:PULSe:TDELay[1] 63
- [:AMPlitude] 67
- [:SOURce]:PULSe:WIDTh[1] 68
- [:SOURce]:ROSCillator:SOURce 68
- Amplitude 70
- Offset = 72
- High–Low 73
- :STATus:PRESet 76
- :SYSTem:CHECk[:ALL][:STATe] 78
- :SYSTem:ERRor? 78
- :SYSTem:KEY 79
- :SYSTem:PRESet 81
- :SYSTem:SECurity[:STATe] 82
- :SYSTem:SET 83
- :SYSTem:VERSion? 83
- :SYSTem:WARNing[:COUNt]? 83
- :SYSTem:WARNing:STRing? 84
- :SYSTem:WARNing:BUFFer? 84
- :TRIGger[:SEQuence[1]]:COUNt 84
- :TRIGger:IMPedance 85
- :TRIGger:LEVel 86
- :TRIGger:SLOPe 86
- 3Specifications 89
- Manufacturer 90
- Supplementary 90
- Information 90
- Agilent 81101A Specifications 91
- Recalibration period 92
- Acoustic Noise Emission 92
- Timing Specifications 93
- Transition Times 95
- Level Specifications 96
- Clock Sources 97
- Clock / PLL Reference Input 98
- Phase Locked Loop (PLL) 98
- Output Modes 99
- Trigger Modes 100
- Trigger Output 101
- Strobe Output 101
- Typical Delays 102
- Human Interface 103
- Remote Control 104
- Pulse Parameter Definitions 105
- Time Reference Point 106
- Pulse Period 106
- Trigger Delay 106
- Pulse Width 106
- Pulse Delay 107
- Double Pulse Delay 107
- Interchannel Delay (Skew) 107
- Transition Time 108
- Linearity 108
- Stability 109
- Pulse Levels 109
- Preshoot, Overshoot, Ringing 110
- Settling Time 110
- Repeatability 111
- Specifications 112
- Front Panel Controls 117
- Edition E0300 118
- Printed in Germany 118
- 81101-91021 118
- DECLARATION OF CONFORMITY 123
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies 222A
(24 pages)
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels