Agilent Technologies Agilent 8166A Manuel d'instructions Page 55
- Page / 274
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Agilent 8163A/B, 8164A/B & 8166A/B Mainframes, Fifth Edition 55
3
Instrument Setup and Status
This chapter gives descriptions of commands that you can use when
setting up your instrument. The commands are split into the following
separate subsytems:
• IEEE specific commands that were introduced in “Common Commands”
on page 29.
• STATus subsystem commands that relate to the status model.
• SYSTem subsystem commands that control the serial interface and
internal data.
IEEE-Common Commands . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Status Reporting – The STATus Subsystem. . . . . . . . . . . . 64
Interface/Instrument Behaviour Settings – The SYSTem
Subsystem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
- Programming Guide 1
- 08164-90B64 2
- Warnings and Notices 3
- In this Manual 5
- Related Manuals 6
- Table of Contents 7
- Specific Commands 43 8
- VISA Programming Examples 189 9
- Error Codes 257 10
- Index 271 10
- List of Figures 11
- List of Tables 13
- Introduction to Programming 15
- GPIB Interface 16
- Figure 1 Remote Control 18
- Message Queues 19
- How the Input Queue Works 20
- The Output Queue 21
- The Error Queue 22
- Programming and Syntax 23
- Diagram Conventions 23
- Short Form and Long Form 24
- Command and Query Syntax 25
- Data Types 26
- Slot and Channel Numbers 26
- Laser Selection Numbers 27
- Common Commands 29
- Common Command Summary 30
- Common Status Information 31
- The Status Model 33
- Status Byte Register 35
- Status Summary 35
- Status System for 8166A/B 36
- Annotations 37
- Status Command Summary 40
- Other Commands 41
- Specific Commands 43
- Specific Command Summary 44
- page 154 46
- :TRIGger 53
- :TRIGger:CONFiguration 53
- :TRIGger[n][CHANnel[m]] 53
- Instrument Setup and Status 55
- IEEE-Common Commands 56
- • GPIB (interface) state 61
- • Output queue 61
- Settings – The SYSTem 76
- → +20<END> 78
- Root Layer Command 80
- → #536570 83
- → 1200e-6,2.019\n 1210e-6 84
- Measurement Functions – The 85
- SENSe Subsystem 85
- Measurement Running 94
- Measurement Stopped 94
- → interpreted as 98
- → +1.00000000E+000<END> 102
- → -2.00000000E+001<END> 103
- → 1<END> 104
- → +6.5000E+001 110
- → +8.00000000E-002<END> 111
- → +1.80000000E-001<END> 112
- Subsystem 113
- → HIGH<END> 114
- → +0<END> 116
- → 0<END> 117
- → 50<END> 118
- → +1<END> 119
- → +4.00000E+03<END> 120
- → +8.000E+01<END> 121
- [PM 130
- → -1.00000000E+013<END> 135
- → +1.5500000E-006<END> 135
- <wsp> 137
- <value> 137
- → +3<END> 137
- → +5.00000000E-001<END> 138
- → STEP<END> 141
- → ONEW<END> 142
- → +5.00000000E-008<END> 143
- → +1.50000000E-006<END> 144
- → +1.55000000E-006<END> 145
- manual sweep 146
- → +5.00000000E-009<END> 147
- Signal Conditioning 148
- → 2<END> 149
- → 12<END> 152
- → 6<END> 153
- Offset ( λ ) 161
- → +2,+1<END> 162
- UM 163
- 163
- → 1000 entries) 164
- Slot Numbers 165
- Command Semantic 166
- Display and System Commands 167
- IEEE Commands 167
- Status Commands 168
- User Calibration Data 168
- Signal Routing 169
- Triggering - The TRIGger 171
- → ign<END> 174
- → 5<END> 175
- → dis<END> 176
- ..... 180
- Tun able 182
- Display Operations – The 186
- DISPlay Subsystem 186
- VISA Programming Examples 189
- How to Use VISA Calls 190
- How to Set up a Fixed Laser 192
- How to Measure Power using 195
- FETCh and READ 195
- How to Co-ordinate Two 199
- How Power Varies with 203
- Wavelength 203
- How to Log Results 207
- Installing the Agilent 816x 214
- Instrument Driver 214
- Using Visual Programming 218
- Environments 218
- Getting Started with LabView 221
- Features of the Agilent 816x 225
- Directory Structure 226
- Opening an Instrument Session 227
- Closing an Instrument Session 228
- VISA Data Types and Selected 229
- Constant Definitions 229
- Error Handling 230
- Agilent VEE 5.01 (or higher) 233
- Online Information 234
- Lambda Scan Applications 235
- Equally Spaced Datapoints 236
- Scan Application 239
- Laser Source 245
- Compatibility Issues 246
- Status Model 247
- Preset Defaults 248
- Removed Command 249
- Obsolete Commands 250
- Changed Parameter Syntax and 251
- Semantics 251
- Changed Query Result Values 252
- Timing Behavior 253
- Command Order 255
- Instrument Status Settings 256
- Error Codes 257
- GPIB Error Strings 258
- Agilent Technologies 274
Produits connexes et manuels pour Multimètres Agilent Technologies Agilent 8166A
(144 pages)
(21 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels