Agilent Technologies 8000 Series Spécifications Page 14
- Page / 162
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 1: General Information
Accessories available
14
Accessories available
The following accessories are available for use with the Agilent Technologies Infiniium
oscilloscope. Other accessories may be available. See your Agilent Technologies Sales
Representative or visit www.agilent.com.
Table 1-1
8000 Series Oscilloscope Accessories
1130A 1.5 GHz InfiniiMax Differential and Single-Ended Probe Amplifier
E2669A InfiniiMax Connectivity Kit for Differential and Single-Ended Measurements
E2668A InfiniiMax Connectivity Kit for Single-Ended Measurements
E2675A InfiniiMax Differential Browser Probe Head
E2676A InfiniiMax Single-Ended Browser Probe Head
E2677A InfiniiMax Differential Solder-in Probe Head
E2678A InfiniiMax Differential and Single-Ended Socketed Probe Head
E2679A InfiniiMax Single-Ended Solder-in Probe Head
E2695A InfiniiMax Differential SMA Probe Head
1144A 800 MHz Active Probe
Requires 1142A power supply
1145A 750 MHz 2-Channel, Low-Mass Active Probe
Requires 1142A power supply
01144-61604 1:2 Probe Power Fan-Out
To provide power for two 1144A or 1145A probes
1146A 10 kHz, 100 A AC/DC Current Probe
1147A 50 MHz, 50 A AC/DC Current Probe
1153A 200 MHz Differential Probe
1155A 750 MHz 2-Channel, Low-Mass Active Probe
1156A 1.5 GHz Active Probe
10070C 1:1 1 M
Ω Passive Probe
10073C 10:1 2.2 M
Ω Passive Probe
1162A 1:1 1 M
Ω Passive Probe
1163A 10:1 500
Ω, Low-C Resistive Divider Passive Probe
1165A 10:1 10 M
Ω Passive Probe
1171A Low-Mass, Miniature 10:1 10 M
Ω Passive Probe
10833A GPIB cable, 1 m
10833B GPIB cable, 2 m
10833C GPIB cable, 4 m
10833D GPIB cable, 0.5 m
54006A 6 GHz, 10:1 500 Ω or 20:1 1 kΩ Resistor Divider Probe
E2609B Rackmount Kit
1184A Testmobile with accessory drawer and tray for mouse/keyboard
- Service Guide 1
- In This Book 5
- Contents 7
- 6 Replacing Assemblies 8
- 7 Replaceable Parts 8
- 8 Theory of Operation 8
- General Information 10
- Accessories supplied 13
- Accessories available 14
- Options available 15
- ± 5°C from the temperature 16
- Environmental Conditions 17
- Measurement Category 17
- Oscilloscope Dimensions 18
- Preparing for Use 19
- Setting Up the Oscilloscope 20
- To inspect package contents 21
- Figure 2-1 21
- To connect power 22
- Attaching the Probe Connector 25
- Probing the Circuit 26
- To connect the digital probe 28
- Digital probe lead set 29
- 40-pin Connector Pinout 30
- Figure 2-14 31
- To turn on the oscilloscope 32
- To turn off the oscilloscope 32
- Probe Compensation 33
- To clean the oscilloscope 35
- Testing Performance 37
- Clear Display 39
- Averaging 39
- Specifications 39
- Performance Test Procedures 39
- Fluke MET/CAL Procedures 39
- To test the DC calibrator 40
- To test input resistance 42
- Connect the equipment 43
- Select Close 45
- (Supply) Minimum Maximum 45
- Set the scale from the 46
- Set the offset from the 46
- To test bandwidth 47
- To verify threshold accuracy 49
- Connections 50
- High-to-Low Transitions 55
- Threshold Voltage Setting V2 56
- Low-to-High Transitions 57
- To test time scale accuracy 59
- Oscilloscope 60
- Sine Wave Source 60
- Frequency Reference 60
- Agilent Technologies 64
- Range Supply Limits 65
- Performance Test Record 66
- Calibrating and Adjusting 67
- To run the self calibration 69
- Troubleshooting 71
- Default Setup 73
- 54830F01a 75
- Primary Trouble Isolation 76
- Run oscilloscope self-tests 77
- Self Calibration 78
- Performance” on page 37 78
- No Display Trouble Isolation 79
- Input Pin # 7 65432 1 81
- Replace any shorted assembly 84
- Replace the power supply 84
- To check probe power outputs 85
- To Check the keyboard 86
- To check the LEDs 87
- Intel D915GUX Motherboard 88
- To Reset 89
- 5 and 7 89
- To setup the BIOS 91
- Figure 5-12 93
- Software Revisions 94
- Replacing Assemblies 95
- Bottom sleeve fasteners 99
- Removing bottom sleeve 100
- Connecting Mylar flex sables 101
- Disconnecting W8 104
- Access Hole 105
- Removing the BNC nuts 108
- Figure 6-17 112
- Opening in side of 131
- Fan control board cables 131
- Acquisition board cables 131
- Figure 6-32 132
- Lift board out of chassis 134
- To remove and replace a fan 135
- Mylar flex cables 136
- T10 Torx Screws 136
- Replaceable Parts 137
- Power Cords 139
- Exploded Views 140
- Replaceable Parts List 145
- Theory of Operation 149
- Figure 8-1 150
- Logic Trigger 154
- Attenuator Theory 155
- Acquisition Theory 155
- • Trigger levels 156
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies 8000 Series
(92 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels