Agilent Technologies 8000 Series Spécifications Page 146
- Page / 162
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 7: Replaceable Parts
Replaceable Parts List
146
W18 8120-1703 1 CABLE-POWER (Option 900-UK)
W18 8120-0696 1 CABLE-POWER (Option 901-AUSTL)
W18 8120-1692 1 CABLE-POWER (Option 902-EUR)
W18 8120-2296 1 CABLE-POWER (Option 906-SWIT)
W18 8120-2957 1 CABLE-POWER (Option 912-DEN)
W18 8120-4600 1 CABLE-POWER (Option 917-AFRICA)
W18 8120-4754 1 CABLE-POWER (Option 918-JAPAN)
W18 8120-6799 1 CABLE-POWER (Option 919-ISRAEL)
W18 8120-6871 1 CABLE-POWER (Option 920-ARGENTINA)
W18 8120-6979 1 CABLE-POWER (Option 921-CHILE)
W18 8120-8377 1 CABLE-POWER (Option 922)
W18 8120-8871 1 CABLE-POWER (Option 927-THAILAND)
Electrical Assemblies
A2 D8064-62601 1 POWER SUPPLY SUBASSEMBLY
A5 0950-4635 1 INVERTER BOARD
A13 2090-0911 1 LCD XGA DISPLAY
MP46 54858-66513 1 USB TOUCHSCREEN CONTROLLER BOARD, PROGRAMMED
A22 54857-61201 1 CAL BRACKET SUBASSEMBLY
PC Motherboard
A4 0960-2522 1 CONVERTER CARD-ATAPI TO SATA
A6 0950-4741 1 CD ROM Drive
A8 1 HARD DISK DRIVE with SOFTWARE (NOT ON OPTION 017 REMOVABLE
DRIVE)
DSO/MSO8000A (with Intel motherboard): Part number D81004-68701
DSO/MSO8000A (with ADLINK motherboard): Part number D81004-68702
5483xA/D, 5485xA: Part number 54855-68704
Replace A19 motherboard with same type.
A19 D81004-68703 1 MOTHERBOARD SUBASSEMBLY (Includes new deck and heat sink.)
A19 D81004-68809 1 MOTHERBOARD SUBASSEMBLY
A19 D8104-68700 1 MOTHERBOARD SUBASSEMBLY
All Configurations
A9 54810-66506 1 PROBE INTERFACE BOARD
A12 0960-2530 1 DISPLAY BOARD (installed only with Intel motherboard)
A16 54832-68703
0
4-CH REPLACEMENT I/O KIT (DSO models)
A16 54838-68703
0
4-CH REPLACEMENT I/O KIT (MSO models)
A17 54826-66507 1 KEYBOARD - CURSOR
A18 54832-66504 1 KEYBOARD - 4CH (DSO models)
A18 54826-66504 1 KEYBOARD - 4CH (MSO models)
A20 D8064-66401
1
FAN CONTROLLER BOARD
A21 54855-66515
1
INTERFACE & GPIB BOARD
Fans
B1 3160-4134 6 12 V FAN
Internal Chassis Parts
H1 0515-2219 3 SCREW-MACH; M2.5 X 0.45 5MM-LG ; T8
H2 54503-25701 4 HEX NUT BNC
H3 0515-1025 3 SCREW-MACH; M3 X 0.5 26MM-LG; T10; WASHER
H4 0515-1410 4 SCREW-MACH; M3 X 0.5 20MM-LG; T10; PAN; WASHER
H5 0515-0430 13 SCREW-MACH; M3 X 0.5 6MM-LG; T10; PAN; WASHER
Replaceable Parts
Ref.
Des.
Agilent Part
Number Qty Description
- Service Guide 1
- In This Book 5
- Contents 7
- 6 Replacing Assemblies 8
- 7 Replaceable Parts 8
- 8 Theory of Operation 8
- General Information 10
- Accessories supplied 13
- Accessories available 14
- Options available 15
- ± 5°C from the temperature 16
- Environmental Conditions 17
- Measurement Category 17
- Oscilloscope Dimensions 18
- Preparing for Use 19
- Setting Up the Oscilloscope 20
- To inspect package contents 21
- Figure 2-1 21
- To connect power 22
- Attaching the Probe Connector 25
- Probing the Circuit 26
- To connect the digital probe 28
- Digital probe lead set 29
- 40-pin Connector Pinout 30
- Figure 2-14 31
- To turn on the oscilloscope 32
- To turn off the oscilloscope 32
- Probe Compensation 33
- To clean the oscilloscope 35
- Testing Performance 37
- Clear Display 39
- Averaging 39
- Specifications 39
- Performance Test Procedures 39
- Fluke MET/CAL Procedures 39
- To test the DC calibrator 40
- To test input resistance 42
- Connect the equipment 43
- Select Close 45
- (Supply) Minimum Maximum 45
- Set the scale from the 46
- Set the offset from the 46
- To test bandwidth 47
- To verify threshold accuracy 49
- Connections 50
- High-to-Low Transitions 55
- Threshold Voltage Setting V2 56
- Low-to-High Transitions 57
- To test time scale accuracy 59
- Oscilloscope 60
- Sine Wave Source 60
- Frequency Reference 60
- Agilent Technologies 64
- Range Supply Limits 65
- Performance Test Record 66
- Calibrating and Adjusting 67
- To run the self calibration 69
- Troubleshooting 71
- Default Setup 73
- 54830F01a 75
- Primary Trouble Isolation 76
- Run oscilloscope self-tests 77
- Self Calibration 78
- Performance” on page 37 78
- No Display Trouble Isolation 79
- Input Pin # 7 65432 1 81
- Replace any shorted assembly 84
- Replace the power supply 84
- To check probe power outputs 85
- To Check the keyboard 86
- To check the LEDs 87
- Intel D915GUX Motherboard 88
- To Reset 89
- 5 and 7 89
- To setup the BIOS 91
- Figure 5-12 93
- Software Revisions 94
- Replacing Assemblies 95
- Bottom sleeve fasteners 99
- Removing bottom sleeve 100
- Connecting Mylar flex sables 101
- Disconnecting W8 104
- Access Hole 105
- Removing the BNC nuts 108
- Figure 6-17 112
- Opening in side of 131
- Fan control board cables 131
- Acquisition board cables 131
- Figure 6-32 132
- Lift board out of chassis 134
- To remove and replace a fan 135
- Mylar flex cables 136
- T10 Torx Screws 136
- Replaceable Parts 137
- Power Cords 139
- Exploded Views 140
- Replaceable Parts List 145
- Theory of Operation 149
- Figure 8-1 150
- Logic Trigger 154
- Attenuator Theory 155
- Acquisition Theory 155
- • Trigger levels 156
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies 8000 Series
(92 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels