Agilent Technologies 8000 Series Spécifications Page 145
- Page / 162
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 7: Replaceable Parts
Replaceable Parts List
145
Replaceable Parts List
The following table is a list of replaceable parts and is organized as follows:
• Exchange assemblies in alphanumeric order by reference designation.
• External chassis parts in alphanumeric order by reference designation. These parts are
generally those that take the physical wear and tear of use.
• Internal parts in several categories. Each category is in alphanumeric order by reference
designation. Replacing these parts generally requires opening the cabinet.
The information given for each part consists of the following:
• Reference designation.
• Agilent Technologies part number.
• Total quantity (Qty) in an oscilloscope or on an assembly. The total quantity is given once and
at the first appearance of the part number in the list.
• Description of the part.
Replaceable Parts
Ref.
Des.
Agilent Part
Number Qty Description
Exchange Assemblies
A1 54831-66523 1 4-CH ACQUISITION ASSEMBLY (DSO8064A)
A1 54832-66523 1 4-CH ACQUISITION ASSEMBLY (DSO8104A)
A1 54831-66524 1 4-CH ACQUISITION ASSEMBLY (MSO8064A)
A1 54832-66524 1 4-CH ACQUISITION ASSEMBLY (MSO8104A)
External Chassis Parts
MP13 54801-47403 1 KNOB 24 MM GRAY
MP14 54801-47408 1 KNOB 18 MM YELLOW
MP15 54801-47404 1 KNOB 12 MM YELLOW
MP16 54801-47409 1 KNOB 18 MM GREEN
MP17 54801-47405 1 KNOB 12 MM GREEN
MP18 54801-47410 1 KNOB 18 MM PURPLE
MP19 54801-47406 1 KNOB 12 MM PURPLE
MP 20 54801-47411 1 KNOB 18 MM PINK
MP21 54801-47407 1 KNOB 12 MM PINK
MP22 54801-47401 4 KNOB 12 MM GRAY
MP26 54832-94330 1 FRONT PANEL 4-CH LABEL (DSO models)
MP26 54838-94330 1 FRONT PANEL 4-CH LABEL (MSO models)
MP28 D8064-94301 1 LOGO LABEL (DSO8064A)
MP28 D8104-94301 1 LOGO LABEL (DSO8104A)
MP28 M8064-94301 1 LOGO LABEL (MSO8064A)
MP28 M8104-94301 1 LOGO LABEL (MSO8104A)
MP31 54810-68701 1 ACCESSORY POUCH
NOT SHOWN
54810-42201 1 FRONT PANEL COVER
MP32 5042-1798 2 REAR FEET
MP34 54810-44901 1 MOLD OVER HANDLE
MP35 54810-45001 2 END CAP HANDLE
MP36 54810-61001 4 BOTTOM FEET w/INSERT
MP37 54810-03702 1 TILT STAND
MP38 01680-41002 4 SIDE FOOT
MP43 D8104-94302 1 USB LABEL
W18 8120-1521 1 CABLE-POWER (standard 125V USA)
- Service Guide 1
- In This Book 5
- Contents 7
- 6 Replacing Assemblies 8
- 7 Replaceable Parts 8
- 8 Theory of Operation 8
- General Information 10
- Accessories supplied 13
- Accessories available 14
- Options available 15
- ± 5°C from the temperature 16
- Environmental Conditions 17
- Measurement Category 17
- Oscilloscope Dimensions 18
- Preparing for Use 19
- Setting Up the Oscilloscope 20
- To inspect package contents 21
- Figure 2-1 21
- To connect power 22
- Attaching the Probe Connector 25
- Probing the Circuit 26
- To connect the digital probe 28
- Digital probe lead set 29
- 40-pin Connector Pinout 30
- Figure 2-14 31
- To turn on the oscilloscope 32
- To turn off the oscilloscope 32
- Probe Compensation 33
- To clean the oscilloscope 35
- Testing Performance 37
- Clear Display 39
- Averaging 39
- Specifications 39
- Performance Test Procedures 39
- Fluke MET/CAL Procedures 39
- To test the DC calibrator 40
- To test input resistance 42
- Connect the equipment 43
- Select Close 45
- (Supply) Minimum Maximum 45
- Set the scale from the 46
- Set the offset from the 46
- To test bandwidth 47
- To verify threshold accuracy 49
- Connections 50
- High-to-Low Transitions 55
- Threshold Voltage Setting V2 56
- Low-to-High Transitions 57
- To test time scale accuracy 59
- Oscilloscope 60
- Sine Wave Source 60
- Frequency Reference 60
- Agilent Technologies 64
- Range Supply Limits 65
- Performance Test Record 66
- Calibrating and Adjusting 67
- To run the self calibration 69
- Troubleshooting 71
- Default Setup 73
- 54830F01a 75
- Primary Trouble Isolation 76
- Run oscilloscope self-tests 77
- Self Calibration 78
- Performance” on page 37 78
- No Display Trouble Isolation 79
- Input Pin # 7 65432 1 81
- Replace any shorted assembly 84
- Replace the power supply 84
- To check probe power outputs 85
- To Check the keyboard 86
- To check the LEDs 87
- Intel D915GUX Motherboard 88
- To Reset 89
- 5 and 7 89
- To setup the BIOS 91
- Figure 5-12 93
- Software Revisions 94
- Replacing Assemblies 95
- Bottom sleeve fasteners 99
- Removing bottom sleeve 100
- Connecting Mylar flex sables 101
- Disconnecting W8 104
- Access Hole 105
- Removing the BNC nuts 108
- Figure 6-17 112
- Opening in side of 131
- Fan control board cables 131
- Acquisition board cables 131
- Figure 6-32 132
- Lift board out of chassis 134
- To remove and replace a fan 135
- Mylar flex cables 136
- T10 Torx Screws 136
- Replaceable Parts 137
- Power Cords 139
- Exploded Views 140
- Replaceable Parts List 145
- Theory of Operation 149
- Figure 8-1 150
- Logic Trigger 154
- Attenuator Theory 155
- Acquisition Theory 155
- • Trigger levels 156
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies 8000 Series
(92 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels