Agilent Technologies 8114A Manuel d'utilisateur télécharger pdf (Page 11)

11

Recommended Conditions

for Low Current and Low

Voltage Measurements

In addition to the conditions

listed in General Specifications,

Agilent Technologies recom-

mends that the following addi-

tional conditions be satisfied for

measuring precise low current

and low voltage with the 4073A.

Note: These conditions are not specified to guarantee a

certain measurement performance.

Auto probers

5

:

TEL P8LC, P12XL

TSK UF200, UF300, UF3000

EG 5|300e

Probe cards

5

:

JEM (Japan Electronic

Materials Co.)

MJC (Micronics Japan Co.)

K&S (Kulicke & Soffa

Industries Inc.)

Temperature: Within ±1°C after

calibration

Temperature change period:

≥10 minutes

Humidity: ≤50 %

Warm up time: ≥60 minutes

Floor vibration: ≤1 mG

Floor vibration frequency: ≥10 Hz

Air cleanliness: ≤class 10,000

Line voltage: Burst noise ≤ 1 kV,

Surge noise ≤1 kV

This line voltage environment

applies EN61326–1

5

Please contact your local sales representative regarding

the latest information on recommended probers and

probe cards

General Specifications

Accuracy is specified at:

Temperature: 23° C ± 5° C

Humidity: 5% to 70% RH

1

Warm up: at least 40 min.

Self-calibration: Within one hour

after calibration

Integration Time: Medium or

Long

2

Regulatory and Standard Compliance:

EMC:

EMC Directive 89/336/EEC,

93/68/EEC

EN61326-1

ICES-001

AS/NZS 2064.1

Safety:

Low Voltage Directive 73/23/

EEC, 93/68/EEC

EN61010-1

CSA C22.2 No.1010.1

UL3111-1

SEMI S2-0200/S8-0999

Operating Temperature Range:

5°C to 30°C

Operating Humidity range:

5% to 70% (no condensation)

Storage Temperature Range:

–20°C to 50°C (< 80% RH, no

condensation)

4

Warm up time: At least 40 minutes

1

5% to 60% RH (no condensation) for isolation

resistance of low current port.

2

For SMU current ranges that are less than or

equal to 1 nA, the integration time must be Long

(16 PLC or longer).

Note: Temperature change after calibration must

be less than 3° C.

3

Line frequency must be 48 Hz to 63 Hz.

4

For an unpacked system, –20° C to 60 °C

(< 90% RH, <12 hrs).

Certification marking

CE, CSA, NRTL/C, C-tick, ICES/

NMB-001

Dimensions

System Cabinet:

600 mm (W) by 900 mm (D) by

1600 mm (H)

Testhead:

640 mm (W) by 642 mm (D) by

400 mm (H)

Weight

System Cabinet:

250 kg (including 3458A,

81110A × 4, 8114A and system

controller)

Note: Cabinet weight approximately 4 kg

less using 5 HV-SPGUs instead of 4

81110As and an 8114A.

Testhead:

70 kg (including 4 SMUs and

48 pins)

Power Requirement

Nominal Allowable Required

Line Voltage Maximum

Voltage

3

Range Current

200 Vac 180 - 220 Vac 20 A

208 Vac 188 - 228 Vac 24 A

220 Vac 198 - 242 Vac 20 A

240 Vac 216 - 252 Vac 20 A

1 2 ... 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire