Agilent-technologies 34401A Manuel d'utilisateur Page 125
- Page / 242
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CONFigure:VOLTage:DC {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}
Preset and configure the multimeter for dc voltage measurements with
the specified range and resolution. This command does not initiate the
measurement.
CONFigure:VOLTage:DC:RATio {<
range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}
Preset and configure the multimeter for dc:dc ratio measurements with
the specified range and resolution. This command does not initiate the
measurement. For ratio measurements, the specified range applies to
the signal connected to the
Input terminals. Autoranging is automatically
selected for reference voltage measurements on the
Sense terminals.
CONFigure:VOLTage:AC {<
range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}
Preset and configure the multimeter for ac voltage measurements with
the specified range and resolution. This command does not initiate the
measurement. For ac measurements, resolution is actually fixed at
6
1
⁄
2
digits. The resolution parameter only affects the front-panel display.
CONFigure:CURRent:DC {<
range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}
Preset and configure the multimeter for dc current measurements with
the specified range and resolution. This command does not initiate the
measurement.
CONFigure:CURRent:AC {<
range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}
Preset and configure the multimeter for ac current measurements with
the specified range and resolution. This command does not initiate the
measurement. For ac measurements, resolution is actually fixed at
6
1
⁄
2
digits. The resolution parameter only affects the front-panel display.
CONFigure:RESistance {<
range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}
Preset and configure the multimeter for 2-wire ohms measurements
with the specified range and resolution. This command does not initiate
the measurement.
CONFigure:FRESistance {<
range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}
Preset and configure the multimeter for 4-wire ohms measurements
with the specified range and resolution. This command does not initiate
the measurement.
4
Chapter 4 Remote Interface Reference
The MEASure? and CONFigure Commands
119
- Agilent 34401A 1
- 6 ½ Digit Multimeter 1
- Safety Information 3
- Additional Notices 5
- DECLARATION OF CONFORMITY 6
- Multimeter 7
- The Front Panel at a Glance 8
- Display Annunciators 10
- The Rear Panel at a Glance 11
- In This Book 12
- Contents 13
- Quick Start 17
- ERROR annunciator turns on 19
- To Adjust the Carrying Handle 22
- To Measure Voltage 23
- To Measure Resistance 23
- To Measure Current 24
- To Test Continuity 25
- To Check Diodes 25
- To Select a Range 26
- To Set the Resolution 27
- -H.DDD,DDD EFFF 28
- -045.23 mVDC 28
- Agilent System II 29
- Front-Panel 31
- Menu Operation 31
- FUNCTION and RANGE / DIGITS 32
- Front-Panel Menu Reference 33
- A Front-Panel Menu Tutorial 35
- Recall 39
- Null 42
- < < 42
- Auto/Man 42
- To Make dB Measurements 46
- To Make dBm Measurements 47
- To Trigger the Multimeter 48
- Using an External Trigger 48
- To Use Reading Hold 49
- To Use Reading Memory 52
- Mem annunciator 53
- Features and 55
- Functions 55
- Features and Functions 56
- Measurement Configuration 57
- Ω and 1000 Ω 58
- DC Input Resistance 59
- Input terminals 61
- Integration Time 63
- Integration Time 63
- Resolution 63
- FRON” or “REAR” 64
- Autozero 65
- RANGE keys to select 68
- Math Operations 69
- Min–Max Operation 70
- Null (Relative) Operation 71
- Limit Testing 75
- Trigger Source Choices 79
- Trig annunciator turns on 80
- GPIB or RS-232) 81
- GPIB interface by 81
- GET using BASIC 81
- Group Execute Trigger 81
- Number of Samples 83
- Number of Triggers 84
- Trigger Delay 85
- Automatic Trigger Delays 87
- Reading Hold 88
- Voltmeter Complete Terminal 89
- External Trigger Terminal 89
- System-Related Operations 90
- Reading Memory 90
- Error Conditions 91
- Self-Test 92
- Display Control 93
- Shift are disabled 93
- Beeper Control 94
- Comma Separators 95
- Firmware Revision Query 95
- SCPI Language Version Query 96
- GPIB Address 97
- Remote Interface Selection 98
- Parity Selection (RS-232) 99
- GPIB / 488 100
- Calibration Overview 101
- Calibration Security 101
- • Front-Panel Operation: 102
- Calibration Count 104
- Calibration Message 105
- Operator Maintenance 106
- Power-On and Reset State 107
- Remote Interface 109
- Reference 109
- > 110
- Command Summary 111
- CONFigure? 111
- (continued) 113
- Command 118
- Using the MEASure? Command 119
- Using the CONFigure Command 119
- Using the READ? Command 120
- Sense terminals 123
- 2-wire ohms) 127
- 4-wire ohms) 127
- Math Operation Commands 130
- Triggering 133
- The Wait-for-Trigger State 135
- Triggering Commands 136
- System-Related Commands 138
- OFF) or “1” (ON) 139
- FIFO) order. Each error 139
- SCPI version 139
- The SCPI Status Model 140
- What is an Event Register? 140
- What is an Enable Register? 140
- SCPI Status System 141
- The Status Byte 142
- IEEE-488 bus 144
- IEEE-488 SRQ interrupt 144
- The Standard Event Register 146
- 148
- Value 148
- Definition 148
- Status Reporting Commands 150
- Calibration Commands 152
- RS-232 Configuration Overview 154
- RS-232 Data Frame Format 155
- DTR / DSR Handshake Protocol 157
- RS-232 Troubleshooting 158
- RS-232 Interface Commands 159
- Command Separators 162
- Querying Parameter Settings 163
- SCPI Command Terminators 163
- IEEE-488.2 Common Commands 164
- SCPI Parameter Types 164
- Output Data Formats 165
- TALK ONLY for Printers 166
- To Set the GPIB Address 167
- On/Off 167
- To Set the Baud Rate 169
- To Set the Parity 170
- 3478A Command 172
- Description 172
- Agilent 34401A Action 172
- Fluke 8840A 173
- Command 173
- Description 173
- Agilent 34401A Action 173
- SCPI Compliance Information 174
- Error 177
- Messages 177
- Error Messages 178
- Execution Errors 179
- SEC is not a valid suffix) 180
- BUS and a READ? 181
- INTERRUPTED 183
- UNTERMINATED 183
- DEADLOCKED 183
- Self-Test Errors 185
- Calibration Errors 186
- Ω range 187
- Application 189
- Programs 189
- Application Programs 190
- Using the Status Registers 194
- Continued on next page > 200
- Measurement 203
- Tutorial 203
- Measurement Tutorial 204
- Thermal EMF Errors 204
- Copper-to 204
- Approx. µV / °C 204
- Loading Errors (dc volts) 205
- Leakage Current Errors 205
- Common Mode Rejection (CMR) 207
- Noise Caused by Ground Loops 208
- Resistance Measurements 209
- 4-Wire Ohms Measurements 209
- Power Dissipation Effects 210
- Settling Time Effects 210
- DC Current Measurement Errors 211
- True RMS AC Measurements 212
- RMS value of a waveform 213
- –3 dB bandwidth 214
- 1 + ( 2 π x F x R 215
- Measurements Below Full Scale 216
- Low-Level Measurement Errors 217
- Common Mode Errors 218
- AC Current Measurement Errors 218
- EMF and bias current errors 219
- Specifications 221
- DC Characteristics 222
- Measuring Characteristics 223
- Chapter 8 Specifications 223
- AC Characteristics 224
- General Information 228
- HOLD Sensitivity: 228
- Product Dimensions 229
- ≤ 150 µV 230
- ≤ 15 µV 230
- ≤ 1.5 µV 230
- ≤ 40 µV 231
- Sensitivity 232
- Resolution 233
- Accuracy 233
- Transfer Accuracy 234
- 24-Hour Accuracy 234
- 90-Day and 1-Year Accuracy 234
- Temperature Coefficients 234
- IndexIndex 237
© 2020, manymanuals.fr. Tous droits réservés | 2.540 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels