Agilent-technologies 34401A Manuel d'utilisateur Page 196
- Page / 242
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
GPIB Operation Using QuickBASIC
REM $Include "QBSetup"
ISC&=7
DEV&=722
INFO1$="*RST"
LENGTH1%=LEN(INFO1$)
INFO2$="*CLS"
LENGTH2%=LEN(INFO2$)
INFO3$="*ESE 1"
LENGTH3%=LEN(INFO3$)
INFO4$="*SRE 32"
LENGTH4%=LEN(INFO4$)
INFO5$="*OPC?"
LENGTH5%=LEN(INFO5$)
INFO6$="CONF:VOLT:DC 10"
LENGTH6%=LEN(INFO6$)
INFO7$="VOLT:DC:NPLC 10"
LENGTH7%=LEN(INFO7$)
INFO8$="TRIG:COUN 100"
LENGTH8%=LEN(INFO8$)
INFO9$="CALC:FUNC AVER;STAT ON"
LENGTH9%=LEN(INFO9$)
INFO10$="INIT"
LENGTH10%=LEN(INFO10$)
INFO11$="*OPC"
LENGTH11%=LEN(INFO11$)
INFO12$="CALC:AVER:AVER?;MIN?;MAX?"
LENGTH12%=LEN(INFO12$)
INFO13$="*CLS"
LENGTH13%=LEN(INFO13$)
DIM A(1:3)
Actual%=0
Reading=0
Continued on next page >
Chapter 6 Application Programs
Using the Status Registers
190
- Agilent 34401A 1
- 6 ½ Digit Multimeter 1
- Safety Information 3
- Additional Notices 5
- DECLARATION OF CONFORMITY 6
- Multimeter 7
- The Front Panel at a Glance 8
- Display Annunciators 10
- The Rear Panel at a Glance 11
- In This Book 12
- Contents 13
- Quick Start 17
- ERROR annunciator turns on 19
- To Adjust the Carrying Handle 22
- To Measure Voltage 23
- To Measure Resistance 23
- To Measure Current 24
- To Test Continuity 25
- To Check Diodes 25
- To Select a Range 26
- To Set the Resolution 27
- -H.DDD,DDD EFFF 28
- -045.23 mVDC 28
- Agilent System II 29
- Front-Panel 31
- Menu Operation 31
- FUNCTION and RANGE / DIGITS 32
- Front-Panel Menu Reference 33
- A Front-Panel Menu Tutorial 35
- Recall 39
- Null 42
- < < 42
- Auto/Man 42
- To Make dB Measurements 46
- To Make dBm Measurements 47
- To Trigger the Multimeter 48
- Using an External Trigger 48
- To Use Reading Hold 49
- To Use Reading Memory 52
- Mem annunciator 53
- Features and 55
- Functions 55
- Features and Functions 56
- Measurement Configuration 57
- Ω and 1000 Ω 58
- DC Input Resistance 59
- Input terminals 61
- Integration Time 63
- Integration Time 63
- Resolution 63
- FRON” or “REAR” 64
- Autozero 65
- RANGE keys to select 68
- Math Operations 69
- Min–Max Operation 70
- Null (Relative) Operation 71
- Limit Testing 75
- Trigger Source Choices 79
- Trig annunciator turns on 80
- GPIB or RS-232) 81
- GPIB interface by 81
- GET using BASIC 81
- Group Execute Trigger 81
- Number of Samples 83
- Number of Triggers 84
- Trigger Delay 85
- Automatic Trigger Delays 87
- Reading Hold 88
- Voltmeter Complete Terminal 89
- External Trigger Terminal 89
- System-Related Operations 90
- Reading Memory 90
- Error Conditions 91
- Self-Test 92
- Display Control 93
- Shift are disabled 93
- Beeper Control 94
- Comma Separators 95
- Firmware Revision Query 95
- SCPI Language Version Query 96
- GPIB Address 97
- Remote Interface Selection 98
- Parity Selection (RS-232) 99
- GPIB / 488 100
- Calibration Overview 101
- Calibration Security 101
- • Front-Panel Operation: 102
- Calibration Count 104
- Calibration Message 105
- Operator Maintenance 106
- Power-On and Reset State 107
- Remote Interface 109
- Reference 109
- > 110
- Command Summary 111
- CONFigure? 111
- (continued) 113
- Command 118
- Using the MEASure? Command 119
- Using the CONFigure Command 119
- Using the READ? Command 120
- Sense terminals 123
- 2-wire ohms) 127
- 4-wire ohms) 127
- Math Operation Commands 130
- Triggering 133
- The Wait-for-Trigger State 135
- Triggering Commands 136
- System-Related Commands 138
- OFF) or “1” (ON) 139
- FIFO) order. Each error 139
- SCPI version 139
- The SCPI Status Model 140
- What is an Event Register? 140
- What is an Enable Register? 140
- SCPI Status System 141
- The Status Byte 142
- IEEE-488 bus 144
- IEEE-488 SRQ interrupt 144
- The Standard Event Register 146
- 148
- Value 148
- Definition 148
- Status Reporting Commands 150
- Calibration Commands 152
- RS-232 Configuration Overview 154
- RS-232 Data Frame Format 155
- DTR / DSR Handshake Protocol 157
- RS-232 Troubleshooting 158
- RS-232 Interface Commands 159
- Command Separators 162
- Querying Parameter Settings 163
- SCPI Command Terminators 163
- IEEE-488.2 Common Commands 164
- SCPI Parameter Types 164
- Output Data Formats 165
- TALK ONLY for Printers 166
- To Set the GPIB Address 167
- On/Off 167
- To Set the Baud Rate 169
- To Set the Parity 170
- 3478A Command 172
- Description 172
- Agilent 34401A Action 172
- Fluke 8840A 173
- Command 173
- Description 173
- Agilent 34401A Action 173
- SCPI Compliance Information 174
- Error 177
- Messages 177
- Error Messages 178
- Execution Errors 179
- SEC is not a valid suffix) 180
- BUS and a READ? 181
- INTERRUPTED 183
- UNTERMINATED 183
- DEADLOCKED 183
- Self-Test Errors 185
- Calibration Errors 186
- Ω range 187
- Application 189
- Programs 189
- Application Programs 190
- Using the Status Registers 194
- Continued on next page > 200
- Measurement 203
- Tutorial 203
- Measurement Tutorial 204
- Thermal EMF Errors 204
- Copper-to 204
- Approx. µV / °C 204
- Loading Errors (dc volts) 205
- Leakage Current Errors 205
- Common Mode Rejection (CMR) 207
- Noise Caused by Ground Loops 208
- Resistance Measurements 209
- 4-Wire Ohms Measurements 209
- Power Dissipation Effects 210
- Settling Time Effects 210
- DC Current Measurement Errors 211
- True RMS AC Measurements 212
- RMS value of a waveform 213
- –3 dB bandwidth 214
- 1 + ( 2 π x F x R 215
- Measurements Below Full Scale 216
- Low-Level Measurement Errors 217
- Common Mode Errors 218
- AC Current Measurement Errors 218
- EMF and bias current errors 219
- Specifications 221
- DC Characteristics 222
- Measuring Characteristics 223
- Chapter 8 Specifications 223
- AC Characteristics 224
- General Information 228
- HOLD Sensitivity: 228
- Product Dimensions 229
- ≤ 150 µV 230
- ≤ 15 µV 230
- ≤ 1.5 µV 230
- ≤ 40 µV 231
- Sensitivity 232
- Resolution 233
- Accuracy 233
- Transfer Accuracy 234
- 24-Hour Accuracy 234
- 90-Day and 1-Year Accuracy 234
- Temperature Coefficients 234
- IndexIndex 237
© 2020, manymanuals.fr. Tous droits réservés | 0.238 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels