Agilent Technologies Agilent B2201A Manuel d'utilisateur Page 72
- Page / 234
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3-12 Agilent B2200 User’s Guide, Edition 2
Front Panel Operation
Switch Control Functions
Switch Control Functions
This section introduces the switch control functions of the Agilent B2200.
• “Channel Configuration Mode”
• “Connection Rule”
• “Connection Sequence”
•“Bias Mode”
• “Ground Mode”
• “Couple Mode”
- Agilent B2200A 1
- Agilent B2201A 1
- Manual Part Number 2
- Warranty 2
- Technol o gy Licenses 2
- Restricted Rights Legend 2
- Safety Summary 5
- Safety Symbols 7
- In This Manual 8
- Contents 10
- 1 Introduction 17
- Agilent B2200 Series 19
- Front Panel 20
- Introduction 21
- Figure 1-1 Front Panel View 21
- Rear Panel 22
- Figure 1-2 Rear Panel View 23
- Switch Modules 24
- Specifications 26
- General Specifications 27
- Accessories and Options 31
- 2 Installation 35
- Requirements 37
- Installation 38
- Table 2-1 Power Cable 38
- Operating Environment 39
- Inspection 40
- Installing the B2200 41
- To Set the GPIB Address 42
- To Connect the GPIB Cable 42
- To Install the Switch Module 43
- To Install the Blank Panel 43
- Self-Test 44
- Output Connections 45
- Connector Plates 46
- To Install Interlock Circuit 49
- To Install LED Circuit 50
- Cathode(-) 51
- Anode(+) 51
- To Mount Connectors 52
- 2 − ∅11.3 ∅3.2 2 − M3 x 0.5 53
- 14 11 11 14 53
- Input Connections 54
- Measurement Cable Length 57
- Maintenance 59
- 3 Front Panel Operation 61
- Operation 63
- To Initialize Agilent B2200 64
- To Enable Light Pen 64
- To Change Connection Rule 65
- To Change Connection Sequence 65
- To Control Switch Condition 65
- To save the setup 66
- To load the setup 66
- To Use Bias Mode 67
- To Use Ground Mode 68
- To Use Couple Mode 69
- To Display Firmware Revision 69
- To Display Module Information 69
- To clear error buffer 70
- LED matrix 71
- Switch Control Functions 72
- Channel Configuration Mode 73
- Connection Rule 74
- Connection Sequence 75
- Bias Mode 76
- Ground Mode 78
- Couple Mode 80
- Display Functions 82
- SequenceRule 83
- GndLock Error GndBias 83
- Card Selection key 84
- Function Edit 85
- Function key group 86
- Break_Before_Make 87
- Settings: 01 [ ] 87
- SET VIEW 88
- ENABLE DISABLE 88
- Channel: 01 88
- Channel: No Channel 88
- Channel 01: ENABLED 88
- Setup Menus 90
- Selftest Menu 94
- Enter key 95
- Exit key to return to the 95
- 4 Programming 99
- :ROUT:CONN:RULE ALL,FREE 101
- :ROUT:CONN:SEQ ALL,BBM 101
- Fundamental Commands 102
- Switch Control 103
- Programming Examples 105
- Connecting Input-Output Paths 106
- Using Bias Mode 108
- Using Ground Mode 110
- Using Couple Mode 112
- Saving Input/Output Labels 114
- Capacitance Compensation 118
- Required Conditions 119
- FORCE or SENSE (A) 124
- FORCE or SENSE (B) 124
- Insulator 124
- Triaxial Cable 124
- 5 SCPI Command Reference 127
- Common Commands 130
- Subsystem Commands 139
- SCPI Command Reference 140
- Command Summary 140
- Relay Control Commands 140
- Command Description 140
- Bias Mode Commands 141
- Ground Mode Commands 142
- Couple Mode Commands 143
- :DIAGnostic:TEST:CARD:CLEar 147
- :DIAGnostic:TEST:CARD:STATe? 148
- :DIAGnostic:TEST:FRAMe:CLEar 148
- ENTER @Agb2200;A$ 151
- [:ROUTe]:AGND:PORT 153
- [:ROUTe]:AGND[:STATe] 154
- [:ROUTe]:AGND:UNUSED 155
- [:ROUTe]:BIAS:PORT 158
- [:ROUTe]:BIAS[:STATe] 159
- [:ROUTe]:CLOSe:CARD? 160
- [:ROUTe]:CLOSe[:LIST] 160
- [:ROUTe]:CONNection:RULE 161
- [:ROUTe]:CONNection:SEQuence 162
- [:ROUTe]:COUPle:PORT 163
- [:ROUTe]:COUPle:PORT:DETect 164
- [:ROUTe]:COUPle[:STATe] 165
- [:ROUTe]:FUNCtion 166
- [:ROUTe]:OPEN:CARD 166
- [:ROUTe]:OPEN[:LIST] 167
- [:ROUTe]:SYMBol:CHANnel 168
- [:ROUTe]:SYMBol:PORT 169
- :SYSTem:BEEP 170
- :SYSTem:CCONfig? 170
- :SYSTem:CDEScription? 171
- :SYSTem:CPON 172
- :SYSTem:CTYPe? 173
- :SYSTem:DISPlay:LCD 173
- :SYSTem:DISPlay:LED 174
- :SYSTem:DISPlay:STRing 174
- :SYSTem:ERRor? 175
- :SYSTem:KLC 175
- :SYSTem:MEMOry:COMMent 176
- :SYSTem:MEMOry:DELete 176
- :SYSTem:MEMOry:LOAD 177
- :SYSTem:MEMOry:SAVE 177
- :SYSTem:PEN 178
- :SYSTem:VERSion? 178
- Status Reporting Structure 179
- Status Byte Register 181
- Output Queue 186
- 6 VXI plug&play Driver 187
- System Requirements 189
- Driver Functions 191
- VXI plug&play Driver 220
- 7 Error Messages 221
- Standard SCPI Error Messages 223
- Execution Error 227
- Device-Dependent Errors 228
- Query Errors 229
- B2200 Channel Related Errors 231
Produits connexes et manuels pour Multimètres Agilent Technologies Agilent B2201A
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels