Agilent Technologies 8510C Manuel d'utilisateur télécharger pdf (Page 7)

Measurement Accessories

There are measurement accessories for seven

device connector types: 7 mm, 3.5 mm, 2.92 mm,

2.4 mm, 1.85 mm, 1.0 mm, and Type-N. Calibration

kits include standards that are required for vector

error correction. Verification kits include stan-

dards used to verify system performance specifica-

tions. Test port return cables extend the ports of

the test set and connect to the device under test.

Agilent 85130X adapter sets convert test set ports

to the same connector type (acting as a test port

saver) or to a different connector type.

Electronic calibration

Electronic calibration (ECal) is a precision, single

connection, one- or two-port calibration technique

that uses fully traceable and verifiable electronic

impedance standards. ECal replaces the traditional

calibration technique that uses mechanical stan-

dards. ECal requires fewer connections. It removes

the intensive operator interaction, which is prone

to errors. A full two-port calibration can be accom-

plished with a single connection of the ECal

module and minimal operator interaction. This

results in a faster and more repeatable calibration.

Calibrations for non-insertable devices are equally

convenient and straight forward.

ECal modules are controlled manually or automati-

cally via the Agilent 85097A PC interface module

with control software. The 85097A consists of a PC

interface module, control software, and a power

supply. The 85090 family of RF ECal modules pro-

vides calibration across the complete frequency

range of the 8753C/D/E vector network analyzers.

The 85060 family of microwave ECal modules

provides calibrations through 26.5 GHz for the

8510B/C and 8719/20/22C/D vector network

analyzers.

ECal modules and available options

A, B

Connector type

Frequency range ECal module Available options

model number

7 mm 30 kHz to 6 GHz

85091A 1BN, 1BP, 910, UK6

7 mm 1 GHz to 18 GHz 85060B 001, 1BN, 1BP,

910, UK6

Type-N 30 kHz to 6 GHz

85092A 00F, 00M, 00A,

1BN, 1BP, 910, UK6

Type-N 1 GHz to 18 GHz 85064B 001, 00F, 00M, 00A,

1BN, 1BP, 910, UK6

3.5 mm 30 kHz to 6 GHz

85093A 00F, 00M, 00A, 1BN,

1BP, 910, UK6

3.5 mm 1 GHz to 26.5 GHz 85062B 001,00F, 00M, 00A,

1BN, 1BP, 910, UK6

Options

Option Description

001 Adds a 30 kHz to 6 GHz RF module

00F Replace f/m connectors on ECal module(s) with f/f connectors

00M Replace f/m connectors on ECal module(s) with m/m connectors

00A Adds male-to-male and female-to-female adapters (also adds

a 5/16” 90 N-cm (8 in-lb) torque wrench to 3.5 mm modules)

1BN MIL-STD 45662 calibration certificate

1BP MIL-STD 45662 calibration certificate with measured data

910 Add an extra operating and service manual

UK6 Commercial calibration certificate with measured data

An 85097A PC interface module with control soft-

ware must be ordered to drive all ECal modules.

The 85097A requires a customer-supplied PC meet-

ing the following minimum requirements:

• Windows 95, Windows NT 4.0, or later operating

system

• 486 or later CPU

• 32 MB of RAM

• 10 MB available hard-disk space

• One of the following GPIB interface cards:

82340A/B, 82341C/D, National AT-GPIB/TNT,

National AT-GPIB/TNT (plug&play), or National

PCI-GPIB

1. For ECal modules with sexed (m-f) connectors, the standard modules have one

female and one male connector.

2. RF ECal modules are specified to operate from 300 kHz to 6 GHz, with typical per-

formance down to 30 kHz.

A. 85060 series modules cover a frequency range of 1 GHz to either 18 or 26.5 GHz.

The upper frequency is limited by the connector cutoff frequency. Each module is

supplied with a torque wrench and foam-padded wood storage box.

B. 85090 series modules cover a frequency range of 30 kHz to 6 GHz. Each module is

supplied with a torque wrench and foam-padded wood storage box.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Commentaires sur ces manuels

Pas de commentaire

Agilent Technologies 8510C Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau Agilent Technologies 8510C