Agilent Technologies Agilent 8164A Guide de l'utilisateur Page 127
- Page / 272
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Power Tests Performance Tests
Agilent 81600B Tunable Laser Source Family, Fourth Edition 127
10 Determine the limits of the transmission and attenuation ranges:
a Lower Transmission Band: λ
1
... λ
2
•OSA_λ
1
= OSA_λ
0
- 15 nm
•OSA_
λ
2
= OSA_λ
0
- 0.5 x Attenuation Band
= OSA_λ
0
- 1 nm
b Upper Transmission Band: λ
3
... λ
4
•OSA_λ
3
= OSA_λ
0
+ 0.5 x Attenuation Band
= OSA_λ
0
+ 1 nm
•OSA_
λ
4
= OSA_λ
0
+ 0.5 x Upper Transmission Band
= OSA_
λ
0
+ 15 nm
c Note the values of OSA_λ
1
, OSA_λ
2
, OSA_λ
3
, OSA_λ
4
in the Test
Record.
•OSA_λ
1
= ___________ nm
•OSA_
λ
2
= ___________ nm
•OSA_
λ
3
= ___________ nm
•OSA_
λ
4
= ___________ nm
11 Determine the SSE power values inside the transmission bands:
a Ensure the TLS is set to TLS_λ
0
and is not changed.
b Set the OSA marker to OSA_λ
1
c Check the OSA and note the SSE power value in [pW] in the table as
SSE_power
d Increase the OSA marker wavelength by 1 nm
e Repeat step c and step d until the wavelength is equal to OSA_λ
2
f Set the OSA to OSA_λ
3
g g Repeat step c and step d until the wavelength is equal to OSA_λ
4
.
h Add up all power values inside the transmissions bands to get the
value of power_trans.
Record the "partial noise power level" values in a table in [pW], where
1 pW = 10
-12
W.
- Agilent 81600B 1
- User’s Guide 1
- In This Guide 4
- Table of Contents 5
- Specifications 33 6
- Performance Tests 71 7
- Index 269 8
- List of Figures 9
- Tunable Laser Source Family 11
- General Safety Considerations 12
- Line Power Requirements 13
- Operating Environment 13
- Initial Inspection 13
- Input/Output Signals 14
- Storage and Shipment 14
- Agilent 81600B family modules 15
- Laser Safety Labels 16
- What is a Tunable Laser? 17
- Front Panels 18
- Typical Use Models 19
- Optical Output 21
- Straight Contact 22
- Connector Symbol 22
- Angled Contact 22
- Signal Input and Output 23
- Accessories 25
- Laser Source Modules and 26
- Option 81600B-072 is highly 27
- Module Options 28
- User’s Guides 29
- Accessories Module Options 30
- Specifications 33
- Definition of Terms 35
- General Definitions 36
- (continuous sweep mode) 38
- Effective linewidth 38
- Linewidth 40
- Maximum output power 40
- Mode-hop free tunability 41
- Output isolation 41
- Polarization extinction ratio 42
- Power linearity 43
- Power repeatability 43
- Power stability 44
- Return loss 46
- Side-mode suppression ratio 46
- (SSE) ratio 46
- Wavelength range 48
- Wavelength resolution 49
- Wavelength stability 50
- Laser Source Module 51
- At constant temperature ±1 K 53
- Conditions 66
- Operating Modes: 68
- Coherence Control: 68
- Output Isolation (typ.): 69
- Return Loss (typ.): 69
- Specifications Conditions 70
- Performance Tests 71
- Required Test Equipment 73
- Test Failure 74
- Instrument Specification 74
- Performance Test Instructions 75
- General test Setup 75
- Environment 75
- Wavelength Tests 76
- Wavelength Accuracy 77
- Mode-Hop Free Tuning 81
- Power Tests 88
- Power Stability 107
- Measurement Principle 112
- ≅1407 nm 117
- Test Procedure 123
- Performance Tests Power Tests 130
- Optional Performance Tests 131
- Dynamic Wavelength Accuracy 135
- Analysis 142
- Normalized Sweep Acceleration 145
- Test Records 146
- Test Record 148
- Test Equipment Used 149
- ________nm 151
- Mode Hop Free Tuning 152
- Wavelength Repeatability 153
- Maximum Power Test 154
- Power Flatness 158
- Wavelength Deviation = Wave 179
- Upper Power Levels 212
- Power Linearity 237
- Safety Precautions 245
- Why is it important to clean 246
- What materials do I need for 247
- Cotton swabs 248
- Soft tissues 248
- Pipe cleaner 249
- Compressed air 249
- Additional Cleaning Equipment 250
- Premoistened cleaning wipes 251
- Polymer film 251
- Infrared Sensor Card 251
- Preserving Connectors 252
- Cleaning Instrument Housings 253
- General Cleaning Procedure 254
- Preferred Procedure 255
- Alternative Procedure 255
- Procedure for Stubborn Dirt 255
- An Alternative Procedure 255
- CAUTIONWARNING 261
- How to clean bare fiber ends 265
- Alternative Procedure A 267
- Alternative Procedure B 267
- Other Cleaning Hints 268
- Agilent Technologies 272
Produits connexes et manuels pour Multimètres Agilent Technologies Agilent 8164A
(152 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels