Agilent Technologies 8000 Series Manuel de l'opérateur Page 41
- Page / 126
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Setting Up the 8000 3
8000 Operator’s Manual 41
10 Load the new tubes of filters into the carousel of the filter changer.
See “Loading Filters (Filter Changer only)” on page 40.
11 Select option 3, Change Filters.
12 Enter 8 as the number of filters to change and press ENTER. The
filters expel from the filter changer.
13 When the filter changer stops expelling filters, select option 3,
Change Filters, again.
14 Enter 1 as the number of filters to change and press ENTER. The
remaining filter of the previous type expels from the filter changer
and is replaced with the new filter.
15 Press ESC four times to return to the Ready screen.
Hidden Key Functions
Table 1 Hidden Key Functions
Key Sequence Function
MENU > 0 > 0 Use this key sequence to select the system configuration. Select the option that
corresponds to the number of valves on your 8000.
MENU > 0 > 8 Use this key sequence to select a fixed 1200 baud or a programmable baud. Select
option 2, Programmable Baud.
Note: If you are using the 8000 with other Agilent equipment, the baud rate must be
set to 9600 baud (see “Printer Operation and Communications” on page 103).
MENU > 0 > A Use this key sequence to set the drop volume before sampling. Enter the desired drop
volume and press ENTER. The maximum acceptable value is 1.
Note: The drop volume is an amount of sample that is dispensed through the 8000
needles prior to dispensing samples into the collection tubes to ensure the needles are
purged completely.
MENU > 0 > B Use this key sequence to enable or disable the moving alert. The asterisk (*) displays
next to the current selection. If enabled, the alarm sounds when the dispensing arm is
in motion.
MENU > 0 > C Use this key sequence to enable or disable the delayed start alarm. The asterisk (*)
displays next to the current selection. If the delayed start alarm is enabled, the alarm
sounds prior to the start of the program. See “DISSO Options Screen” on page 69.
- Agilent 8000 1
- Dissolution Sampling 1
- Contents 3
- 4 8000 Operator’s Manual 4
- 8000 Operator’s Manual 5 5
- 6 8000 Operator’s Manual 6
- 8000 Operator’s Manual 7 7
- 8 8000 Operator’s Manual 8
- 8000 Operator’s Manual 9 9
- 10 8000 Operator’s Manual 10
- Electrical Hazards 12
- Information Symbols 14
- Introduction 15
- 8000 with Peristaltic Pump 17
- CC1234xxxx 18
- Setting Up the 8000 19
- Unpacking Your 8000 21
- Installation 22
- Setup of 8000 and Components 34
- Installing the Sample Tray 36
- (Peristaltic Pump only) 37
- Installing the RM Module 38
- External Unit 39
- Hidden Key Functions 41
- 42 8000 Operator’s Manual 42
- 3 Setting Up the 8000 42
- Table 1 Hidden Key Functions 42
- Setting Up the 8000 3 43
- 8000 Operator’s Manual 43 43
- 44 8000 Operator’s Manual 44
- Operating the 8000 45
- 8000 Keypad Options 46
- Operating the 8000 4 47
- 8000 Operator’s Manual 47 47
- Main Menu 48
- 8000 Operator’s Manual 49 49
- 50 8000 Operator’s Manual 50
- 52 8000 Operator’s Manual 52
- 54 8000 Operator’s Manual 54
- 56 8000 Operator’s Manual 56
- 60 8000 Operator’s Manual 60
- Creating a Sample Program 61
- 8000 Operator’s Manual 63 63
- 64 8000 Operator’s Manual 64
- SAMPLE TIME POINT: 000:02 65
- Starting a 8000 Program 66
- 68 8000 Operator’s Manual 68
- DISSO Options Screen 69
- 70 8000 Operator’s Manual 70
- 8000 Operator’s Manual 71 71
- 8000 Operator’s Manual 73 73
- 8000 Operator’s Manual 75 75
- 76 8000 Operator’s Manual 76
- 78 8000 Operator’s Manual 78
- 82 8000 Operator’s Manual 82
- ON R-M PUMP displays 84
- 8000 Operator’s Manual 85 85
- 88 8000 Operator’s Manual 88
- 8000 Operator’s Manual 89 89
- Starting a Program 91
- APP 3/7 Options Screen 93
- 94 8000 Operator’s Manual 94
- Table 2 4 App 3/7 Options 94
- Manual Sample 95
- 96 8000 Operator’s Manual 96
- Automatic Calibration 97
- 1 MANUAL 2 AUTOMATIC 98
- Manual Calibration 99
- Daisy Chaining 102
- 104 8000 Operator’s Manual 104
- 4 Operating the 8000 104
- Agilent Technologies 105
- Preventive Maintenance 106
- Apparatus 3 / 7 107
- Start Immediately 108
- Programmed Clean 108
- Apparatus 1 / 2 111
- Syringe and Seal Replacement 112
- Cleaning the Syringes 113
- Filter Changer (optional) 115
- Report Center Impact Printer 119
- Replacing a Paper Roll 120
- Toggling Your Printer Online 121
- Printer Self Test 121
- Printer Configuration 122
- 124 8000 Operator’s Manual 124
- 8000 Operator’s Manual 125 125
- 126 8000 Operator’s Manual 126
Produits connexes et manuels pour Imprimer et scanner Agilent Technologies 8000 Series
(82 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels