Agilent Technologies 8000 Series Manuel de l'opérateur Page 54
- Page / 126
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
54 8000 Operator’s Manual
4 Operating the 8000
4 Set Bath Temp
4 Vessel Temp
If your system configuration includes a dissolution apparatus with a water bath, select
option 4, Set Bath Temp. If your system configuration includes a dissolution
apparatus with Direct Vessel Heating (DVH), select option 4, Vessel Temp.
Select option 1, Manual, to set the water bath / vessel temperature. Optionally, select
option 2, Program, to set a desired water bath / vessel temperature to download to the
dissolution apparatus. Enter the desired temperature and press ENTER. The DISSO
Parameters screen displays.
5 Com Port ID Select option 5, Com Port ID, to change the communication port identification
number. Your system was shipped with the communication port identification number
set to 01. You can set the identification number to any number between 1 and 99. The
identification number is used when multiple units are connected in series so that the
controlling or master 8000 can start individual units.
Enter the communication port identification number and press ENTER. The DISSO
Parameters screen displays.
6 DDM or Basket Select option 6, DDM or Basket, to select the apparatus type. The Select Basket or
Paddle of DISSO screen displays.
If using baskets, select option 1, Basket. The DISSO Parameters screen displays.
If using paddles and sequential delivery, select option 2, Paddle. The Dosage Delivery
Mode of DISSO screen displays. Select option 1, Sequential, enter a time interval for
the dosage drop and press ENTER. The DISSO Parameters screen displays.
Note: Only use the sequential delivery option if your dissolution apparatus is
equipped with clutches.
If using paddles and simultaneous delivery, select option 2, Paddle. The Dosage
Delivery Mode of DISSO screen displays. Select option 2, Simultaneous. The DISSO
Parameters screen displays.
7 Print Freq The dissolution apparatus status prints at each sample time point. Select option 7,
Print Freq, to set additional times to print the dissolution apparatus status. This option
should be reserved for use when there is more than 30 minutes between sample time
points.
Enter a print frequency and press ENTER. The DISSO Parameters screen displays.
The print frequency timer restarts after each sample time point.
Note: The status does not print if the specified print frequency is less than three
minutes from the sample time point; the sample time point takes precedence.
Table 5 Disso Parameters Options (Apparatus 1 / 2)
Option Function
- Agilent 8000 1
- Dissolution Sampling 1
- Contents 3
- 4 8000 Operator’s Manual 4
- 8000 Operator’s Manual 5 5
- 6 8000 Operator’s Manual 6
- 8000 Operator’s Manual 7 7
- 8 8000 Operator’s Manual 8
- 8000 Operator’s Manual 9 9
- 10 8000 Operator’s Manual 10
- Electrical Hazards 12
- Information Symbols 14
- Introduction 15
- 8000 with Peristaltic Pump 17
- CC1234xxxx 18
- Setting Up the 8000 19
- Unpacking Your 8000 21
- Installation 22
- Setup of 8000 and Components 34
- Installing the Sample Tray 36
- (Peristaltic Pump only) 37
- Installing the RM Module 38
- External Unit 39
- Hidden Key Functions 41
- 42 8000 Operator’s Manual 42
- 3 Setting Up the 8000 42
- Table 1 Hidden Key Functions 42
- Setting Up the 8000 3 43
- 8000 Operator’s Manual 43 43
- 44 8000 Operator’s Manual 44
- Operating the 8000 45
- 8000 Keypad Options 46
- Operating the 8000 4 47
- 8000 Operator’s Manual 47 47
- Main Menu 48
- 8000 Operator’s Manual 49 49
- 50 8000 Operator’s Manual 50
- 52 8000 Operator’s Manual 52
- 54 8000 Operator’s Manual 54
- 56 8000 Operator’s Manual 56
- 60 8000 Operator’s Manual 60
- Creating a Sample Program 61
- 8000 Operator’s Manual 63 63
- 64 8000 Operator’s Manual 64
- SAMPLE TIME POINT: 000:02 65
- Starting a 8000 Program 66
- 68 8000 Operator’s Manual 68
- DISSO Options Screen 69
- 70 8000 Operator’s Manual 70
- 8000 Operator’s Manual 71 71
- 8000 Operator’s Manual 73 73
- 8000 Operator’s Manual 75 75
- 76 8000 Operator’s Manual 76
- 78 8000 Operator’s Manual 78
- 82 8000 Operator’s Manual 82
- ON R-M PUMP displays 84
- 8000 Operator’s Manual 85 85
- 88 8000 Operator’s Manual 88
- 8000 Operator’s Manual 89 89
- Starting a Program 91
- APP 3/7 Options Screen 93
- 94 8000 Operator’s Manual 94
- Table 2 4 App 3/7 Options 94
- Manual Sample 95
- 96 8000 Operator’s Manual 96
- Automatic Calibration 97
- 1 MANUAL 2 AUTOMATIC 98
- Manual Calibration 99
- Daisy Chaining 102
- 104 8000 Operator’s Manual 104
- 4 Operating the 8000 104
- Agilent Technologies 105
- Preventive Maintenance 106
- Apparatus 3 / 7 107
- Start Immediately 108
- Programmed Clean 108
- Apparatus 1 / 2 111
- Syringe and Seal Replacement 112
- Cleaning the Syringes 113
- Filter Changer (optional) 115
- Report Center Impact Printer 119
- Replacing a Paper Roll 120
- Toggling Your Printer Online 121
- Printer Self Test 121
- Printer Configuration 122
- 124 8000 Operator’s Manual 124
- 8000 Operator’s Manual 125 125
- 126 8000 Operator’s Manual 126
Produits connexes et manuels pour Imprimer et scanner Agilent Technologies 8000 Series
(82 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.154 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels