Agilent Technologies B2902 Manuel de service Page 179
- Page / 326
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Agilent B2900 SCPI Command Reference, Edition 2 4- 57
Subsystem Commands
:OUTPut:OFF:MODE
mode=1 or ON enables the automatic output off function. If this function is enabled,
the source output is automatically turned off immediately when the grouped
channels change status from busy to idle.
Query response mode <newline>
mode is 0 or 1, and indicates that the automatic output off function is off or on,
respectively. Response data type is NR1.
Example :OUTP:OFF:AUTO 1
:OUTP2:OFF:AUTO?
:OUTPut:OFF:MODE
Selects the source condition after output off.
Syntax :OUTPut[c]:OFF:MODE mode
:OUTPut[c]:OFF:MODE?
Parameter mode ZERO|HIZ|NORMal (default). Parameter data type is CPD.
mode=NORMal selects the following setup.
• Source function: Voltage source
• Output voltage: 0 V
• Current compliance: 100 A at the 100 A range
• Output relay: off (open or break)
mode=HIZ selects the following setup.
• Output relay: off (open or break)
• Voltage source setup is not changed if the source applies 40 V or less.
• Current source setup is not changed if the source uses the 100 mA range or
lower.
mode=ZERO selects the following setup.
• Source function: Voltage source
• Output voltage: 0 V
• Current compliance: 100 A at the 100 A range
- Agilent B2900 Series 1
- In This Manual 4
- Contents 10
- 1 Programming Basics 17
- SCPI Commands 19
- Moving Between Subsystems 20
- Including Common Commands 21
- Using Queries 21
- Coupled Commands 21
- SCPI Messages 22
- Message Unit Separator 23
- Root Specifier 23
- Query Indicator 23
- Message Terminator 23
- Numeric Suffix 24
- Channel List Parameter 24
- SCPI Command Completion 25
- Data Output Format 28
- Status Data 29
- GPIB Capability 33
- Status Byte 34
- Status System Diagram 35
- Programming Basics 36
- Non-Volatile Settings 39
- 2 Subsystem Command Summary 41
- Setting Source/Measure Unit 44
- Subsystem Command Summary 45
- • [:SOUR[c]]:WAIT:AUTO OFF 54
- =CURRent 58
- •:SENS[c]:WAIT:AUTO OFF 61
- Source Output Ranges 64
- Duty cycle ~ 2.5 % 66
- Duty cycle ~ 99.9999 % 66
- Measurement Ranges 67
- TRANsient device action 69
- ACQuire device action 69
- Trigger is generated after 70
- ARM Layer 71
- TRIGger Layer 71
- Reading Source/Measure Data 77
- STAR and 85
- Using Advanced Functions 91
- 3 Common Commands 105
- 4 Subsystem Commands 123
- CALCulate Subsystem 125
- :CALCulate:CLIMits:MODE 127
- :CALCulate:CLIMits:STATe 127
- :CALCulate:CLIMits:STATe:ANY? 128
- :CALCulate:CLIMits:UPDate 128
- :CALCulate:DATA? 129
- :CALCulate:DATA:LATest? 130
- :CALCulate:DIGital:BIT 130
- :CALCulate:FEED 131
- :CALCulate:LIMit:FAIL? 133
- :CALCulate:LIMit:FUNCtion 134
- :CALCulate:LIMit:STATe 136
- :CALCulate:MATH:DATA? 136
- :CALCulate:MATH:DATA:LATest? 137
- Predefined math expressions 140
- :CALCulate:MATH:STATe 142
- :CALCulate:MATH:UNITs 143
- :CALCulate:OFFSet 143
- :CALCulate:OFFSet:ACQuire 144
- :CALCulate:OFFSet:STATe 144
- DISPlay Subsystem 145
- :DISPlay:ENABle 146
- :DISPlay:VIEW 146
- :DISPlay[:WINDow]:DATA? 147
- :DISPlay[:WINDow]:TEXT:DATA 148
- :DISPlay[:WINDow]:TEXT:STATe 148
- :DISPlay:ZOOM 149
- FETCh Subsystem 150
- :FETCh[:SCALar]? 152
- ATus 153
- Subsystem Commands 154
- Example :FETC:CURR? (@2,1) 154
- FORMat Subsystem 155
- :FORMat:DIGital 156
- :FORMat:ELEMents:CALCulate 156
- :FORMat:ELEMents:SENSe 157
- :FORMat:SREGister 158
- HCOPy Subsystem 159
- LXI Subsystem 160
- :LXI:MDNS:HNAMe[:RESolved]? 161
- :LXI:MDNS:SNAMe:DESired 161
- :LXI:MDNS:SNAMe[:RESolved]? 161
- Other LXI Subsystem Commands 162
- LXI Trigger Events 164
- MEASure Subsystem 166
- MMEMory Subsystem 168
- :MMEMory:COPY 169
- :MMEMory:DELete 170
- :MMEMory:LOAD:MACRo 170
- :MMEMory:LOAD:STATe 170
- :MMEMory:MDIRectory 170
- :MMEMory:MOVE 171
- :MMEMory:RDIRectory 171
- LL]> 172
- :MMEMory:STORe:MACRo 172
- :MMEMory:STORe:STATe 173
- :MMEMory:STORe:TRACe 173
- OUTPut Subsystem 175
- :OUTPut:HCAPacitance[:STATe] 177
- :OUTPut:LOW 178
- :OUTPut:OFF:AUTO 178
- :OUTPut:OFF:MODE 179
- :OUTPut:ON:AUTO 180
- :OUTPut:PROTection[:STATe] 180
- :OUTPut:RECall 181
- :OUTPut:SAVE 181
- :OUTPut[:STATe] 182
- PROGram Subsystem 183
- :PROGram:PON:RUN 184
- :PROGram[:SELected]:APPend 184
- :PROGram[:SELected]:DEFine 184
- :PROGram[:SELected]:EXECute 186
- :PROGram[:SELected]:NAME 187
- :PROGram[:SELected]:STATe 187
- :PROGram[:SELected]:WAIT? 188
- :PROGram:VARiable 188
- READ Subsystem 190
- :READ[:SCALar]? 192
- Tus 193
- SENSe Subsystem 195
- NPLCycles 196
- NPLCycles:AUTO 197
- [:LEVel] 198
- :TRIPped? 198
- RANGe:AUTO 199
- RANGe:AUTO:LLIMit 200
- TO:THReshold 202
- RANGe:AUTO:ULIMit 202
- RANGe[:UPPer] 203
- :SENSe:DATA? 204
- :SENSe:DATA:LATest? 205
- :SENSe:FUNCtion:OFF 205
- :SENSe:FUNCtion:OFF:ALL 206
- :SENSe:FUNCtion:OFF:COUNt? 206
- :SENSe:FUNCtion[:ON] 206
- :SENSe:FUNCtion[:ON]:ALL 207
- :SENSe:FUNCtion[:ON]:COUNt? 207
- :SENSe:FUNCtion:STATe? 207
- :SENSe:REMote 208
- :SENSe:RESistance:MODE 208
- :SENSe:TOUTput:SIGNal 210
- :SENSe:TOUTput[:STATe] 210
- :SENSe:WAIT:AUTO 211
- :SENSe:WAIT:GAIN 212
- :SENSe:WAIT:OFFSet 212
- :SENSe:WAIT[:STATe] 213
- SOURce Subsystem 214
- :AMPLitude] 215
- [:SOURce]:DIGital:DATA 221
- BEFore 223
- [:SOURce]:FUNCtion:MODE 225
- [:SOURce]:FUNCtion[:SHAPe] 225
- [:SOURce]:PULSe:DELay 228
- [:SOURce]:PULSe:WIDTh 229
- [:SOURce]:SWEep:DIRection 229
- [:SOURce]:SWEep:POINts 230
- [:SOURce]:SWEep:RANGing 231
- [:SOURce]:SWEep:SPACing 232
- [:SOURce]:SWEep:STAir 232
- [:SOURce]:TOUTput:SIGNal 233
- [:SOURce]:TOUTput[:STATe] 233
- [:SOURce]:WAIT:AUTO 234
- [:SOURce]:WAIT:GAIN 235
- [:SOURce]:WAIT:OFFSet 235
- [:SOURce]:WAIT[:STATe] 236
- STATus Subsystem 237
- NTRansition 241
- PTRansition 242
- :STATus:PRESet 242
- SYSTem Subsystem 248
- :SYSTem:COMMunicate:ENABle 249
- :SYSTem:COMMunicate:LAN:DHCP 251
- :SYSTem:COMMunicate:LAN:DNS 252
- :SYSTem:COMMunicate:LAN:MAC? 253
- :SYSTem:COMMunicate:LAN:SMASk 254
- :SYSTem:COMMunicate:LAN:WINS 256
- :SYSTem:DATA:QUANtity? 256
- :SYSTem:DATE 257
- :SYSTem:ERRor:ALL? 257
- :SYSTem:ERRor:CODE:ALL? 257
- :SYSTem:ERRor:CODE[:NEXT]? 258
- :SYSTem:ERRor:COUNt? 258
- :SYSTem:ERRor[:NEXT]? 258
- :SYSTem:FAN:MODE 259
- :SYSTem:GROup[:DEFine] 259
- :SYSTem:GROup:RESet 260
- :SYSTem:INTerlock:TRIPped? 260
- :SYSTem:LANGuage 260
- :SYSTem:LFRequency 261
- :SYSTem:LOCK:NAME? 262
- :SYSTem:LOCK:OWNer? 262
- :SYSTem:LOCK:RELease 262
- :SYSTem:LOCK:REQuest? 263
- :SYSTem:PON 263
- :SYSTem:PRESet 264
- :SYSTem:SET 264
- :SYSTem:TIME 264
- :SYSTem:TIME:TIMer:COUNt? 265
- :SYSTem:VERSion? 266
- TRACe Subsystem 267
- :TRACe:FEED 268
- :TRACe:FEED:CONTrol 268
- :TRACe:FREE? 269
- :TRACe:POINts 269
- :TRACe:POINts:ACTual? 270
- :TRACe:STATistic:DATA? 270
- :TRACe:STATistic:FORMat 270
- :TRACe:TSTamp:FORMat 271
- TRIGger Subsystem 272
- 275
- EXT11 275
- 282
- EXT10 282
- 284
- LAN 284
- 285
- 5 Error Messages 287
- No Error 289
- Command Error 290
- Execution Error 294
- Device-Dependent Error 296
- Query Error 297
- B2900 Specific Error 298
- Error Messages 308
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies B2902
(25 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels