Agilent Technologies 81134A Manuel de service télécharger pdf (Page 15)

Connecting to the Instrument via USB Connecting to the Pulse/Pattern Generator for Remote Programming

Agilent 81133A/81134A Pulse Generator Programming Guide, March 2007 15

viClose (defaultRM);

}

Connecting to the Instrument via

USB

NOTE The control PC must have USB capability for USB connections

(Windows NT is not supported).

For connecting over the USB, please refer to the Help delivered

with the USB driver.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 103 104

Programming Guide 1
Important Notice 2
About This Programming Guide 3
Contents 5
OUTPut Commands 39 6
SOURce Commands 45 6
Status Handling Commands 67 6
Troubleshooting 97 7
Introduction 10
SCPI Commands Reference 17
Common Commands 19
Standard Settings 21
DIAGnostic Commands 23
:CAL:TIM 24
DIGital Commands 25
Range Maximum Pattern Length 29
60 – 3360 Mhz 12 Mbit 29
30 – 60 Mhz 6 Mbit 29
15 – 30 Mhz 3 Mbit 29
CROSsover:[VALue] 32
CROSsover:[STATe] 34
DISPlay Commands 35
MEASure Commands 36
:MEASure:FREQuency? 37
:MEASure:PERiod? 38
OUTPut Commands 39
:OUTPut[0 41
:OUTPut0:SOURce 42
:OUTPut[0 43
:OUTPut[1 43
:OUTPut[1 44
:OUTPut:CENTral 44
SOURce Commands 45
[:SOURce]:FUNCtion[:SHAPe] 50
[:SOURce]:FUNCtion:MODe[1 51
[:SOURce]:PHASe[:ADJ][1 53
[:SOURce][:PULSe]:DCYCle[1 54
[:SOURce][:PULSe]:DELay[1 55
[:SOURce][:PULSe]:DESKew[1 56
[:SOURce][:PULSe]:DHOLd[1 56
[:SOURce][:PULSe]:PERiod 57
[:SOURce][:PULSe]:WIDTh[1 58
[:SOURce]:PM[1 59
[:SOURce]:PM[1 59
[:IMMediate][:AMPLitude] 60
[:IMMediate]:OFFSet 61
[:IMMediate]:HIGH 62
[:IMMediate]:LOW 63
[:IMMediate]:TERM 64
[:SOURce]:VOLTage[1 64
[:AMPLitude]? 64
Status Handling Commands 67
:STATus:OPERation 70
:STATus:PRESet 70
:STATus:QUEStionable 71
:STATus:QUEStionable:VOLTage 73
:STATus:QUEStionable:MONotony 76
SYSTem Commands 79
:SYSTem:ERRor? 81
:SYSTem:PRESet 81
:SYSTem:SET 82
:SYSTem:VERSion? 82
:ADDRess 84
:DGATeway 85
TRIGger Commands 86
:TRIGger:SOURce 87
:TRIGger:TERM 88
:TRIGger:TERM:STATE[?] 89
ARM Commands 90
:ARM[:SEQuence][:LAYer]:LEVel 91
:ARM[:SEQuence][:LAYer]:SLOPe 92
:ARM[:SEQuence][:LAYer]:TERM 94
:ARM[:SEQuence][:LAYer]:STOP 95
Troubleshooting 100
5988-7402EN 104

Commentaires sur ces manuels

Pas de commentaire

Agilent Technologies 81134A Manuel de service Page 15

Commentaires sur ces manuels

Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies 81134A