Agilent Technologies EasyEXPERT Guide de l'utilisateur Page 160
- Page / 228
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
10-10 Agilent EasyEXPERT User’s Guide Vol. 2, Edition 1
Error Message
Agilent EasyEXPERT Operation Error
105914 Improper number of Arguments for the A command. Enter the
Arguments correctly.
105915 A pulse base must be between B A and C A.
105916 A pulse peak must be between B A and C A.
105917 A pulse peak and base must be between B V and C V.
105918 A compliance must be between B V and C V.
105919 A compliance must be between B A and C A.
105920 A pulse peak compliance exceeds its output power limit. Compliance
must be between B V and C V.
105921 A pulse peak compliance exceeds its output power limit. Compliance
must be between B A and C A.
105922 A pulse delay time must be between B s and C s.
105923 A does not support pulse delay time. It must be 0.
105924 SMU pulse measurement delay time must be between A s and B s.
105925 SMU pulse averaging count must be between A and B.
105926 A pulse duty cycle must be B % or less if the pulse peak or compliance
exceeds C A.
105927 A pulse width must be between B s and C s if the pulse peak or
compliance exceeds D A.
105928 A pulse base must be between B A and C A if the pulse peak exceeds D
A.
105929 A pulse peak and base must be same polarity if the pulse output exceeds
B V.
105930 The coefficient for High Speed ADC TIME averaging mode must be
between A s and B s.
105931 Invalid value A was specified for the series resistor of B.
Valid option(s): C
105932 N1258A selector is not found.
105933 Communication with N1258A selector interrupted. Connect the cable
properly.
105934 N1258A selector is turned off. Connect the power cable properly.
- Keysight EasyEXPERT Software 1
- For B1500A Users 5
- For B1505A Users 5
- In This Manual 6
- Contents 10
- 6 Remote Control Interface 13
- Sample programs 14
- About socket services 14
- Introduction 15
- Supported Operations 16
- Preparation for Communication 17
- Common Commands 22
- BENCh Subsystem 23
- [:BENCh]:COUNt:RESet 24
- [:BENCh]:LOAD[:SETup] 24
- [:BENCh]:PRESet:CATalog? 24
- [:BENCh]:PRESet:OPEN 24
- [:BENCh]:PRESet:SETup:SELect 25
- [:BENCh][:SELected]:ABORt 26
- [:BENCh][:SELected]:NAME 26
- [:BENCh][:SELected]:NUMBer 26
- [:BENCh][:SELected]:STRing 27
- [:BENCh]:TAG 28
- CALibration Subsystem 29
- :CALibration[:SMU]:ZERO[:ON] 30
- :CALibration[:SMU]:ZERO:PLC 31
- RESult Subsystem 32
- :RESult:FORMat 33
- :RESult:FORMat:ESCape 33
- :RESult:RECycle:ALL 34
- :RESult:RECycle[:LATest] 34
- STANDby Subsystem 35
- SYSTem Subsystem 36
- WORKspace Subsystem 37
- :WORKspace[:SELected]:NAME? 38
- :WORKspace:STATe? 38
- Error Messages 39
- 7 Utilities 41
- System Requirements 43
- Desktop EasyEXPERT 44
- About Desktop EasyEXPERT 45
- To Install Desktop EasyEXPERT 46
- To Start Desktop EasyEXPERT 47
- Execution Mode dialog box 47
- Start EasyEXPERT window 48
- Using 4155B/4156B/4155C/4156C 50
- License Management Tool 53
- License Management Tool GUI 54
- Setup File Converter 55
- Setup File Converter GUI 56
- MDM File Converter 57
- MDM File Converter GUI 58
- Utility Programs 59
- SetupFileConverter.exe 60
- MdmFileConverter.exe 63
- Utilities 72
- 8 Application Library 77
- Application Test Definitions 79
- Application Library 81
- Accuracy 91
- Capacitance (F) 92
- Capa citance (F) 93
- HRSMU, ASU+SMU 94
- Measurement Accuracy 95
- Reading Accuracy (%) 102
- Offset Accuracy (F) 102
- 9 If You Have a Problem 127
- When You Operate B1500 129
- ASU is not Detected 130
- To Simplify the Connections 131
- When You Perform Measurement 132
- )HUULWHEHDGV 134
- 7HVWGHYLFH 134
- Measurement 136
- To Make Backup 138
- To Check Module Slots 138
- To Check ASU/SMU Combination 138
- Data Backup and Recovery 140
- Folders to Backup 141
- To Make Database Backup 141
- To Restore Database Backup 142
- To Make Backup of Other Data 143
- B1500 System Recovery 144
- To Initialize Database 146
- To Restore Database 147
- Updating EasyEXPERT 148
- If You Have a Problem 150
- 10 Error Message 151
- Agilent FLEX Execution Error 182
- DAC test 209
- 3465 IM short test failed 213
- *B1540-90020* 228
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies EasyEXPERT
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.191 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels