Agilent Technologies EasyEXPERT Guide de l'utilisateur Page 190
- Page / 228
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
10-40 Agilent EasyEXPERT User’s Guide Vol. 2, Edition 1
Error Message
Agilent FLEX Execution Error
283 Set linear sweep for MM20.
Only the linear sweep is available for the PWDCV command for the
pulsed CV measurement (MM20).
284 Improper setting of CMU frequency and pulse width.
Pulse width value is out of the range for the CMU output frequency. Set
both frequency value and pulse width value properly.
290 Send WFC to set Cf sweep source.
Before triggering the Cf sweep measurement, send the WFC command
to set the frequency sweep source (oscillator).
301 Line power failure.
303 Excess voltage in MPSMU.
Voltage that exceeds maximum voltage at the present current range was
detected by a MPSMU. All output switches were set to OFF.
304 Ground unit abuse is detected.
305 Excess current in HPSMU.
Current that exceeds maximum current at the present voltage range was
detected by a HPSMU. All output switches were set to OFF.
307 Unsupported module.
This module is not supported by this firmware revision. Until you
update the firmware, use Agilent B1500 with this module removed.
309 Unknown emergency occurred.
All modules stopped their output and opened their output relay.
310 Interlock open operation error. Initialized.
Initialization was automatically performed because the B1500 failed to
set its output to 0 V when the interlock circuit was opened in the high
voltage condition. Any module may be defective. Perform self-test.
311 ASU control cable was connected/disconnected.
The B1500 must be turned off when the Atto Sense and Switch Unit
(ASU) is connected/disconnected.
312 SCUU control cable was connected/disconnected.
The B1500 must be turned off when the SMU CMU Unify Unit
(SCUU) is connected/disconnected.
- Keysight EasyEXPERT Software 1
- For B1500A Users 5
- For B1505A Users 5
- In This Manual 6
- Contents 10
- 6 Remote Control Interface 13
- Sample programs 14
- About socket services 14
- Introduction 15
- Supported Operations 16
- Preparation for Communication 17
- Common Commands 22
- BENCh Subsystem 23
- [:BENCh]:COUNt:RESet 24
- [:BENCh]:LOAD[:SETup] 24
- [:BENCh]:PRESet:CATalog? 24
- [:BENCh]:PRESet:OPEN 24
- [:BENCh]:PRESet:SETup:SELect 25
- [:BENCh][:SELected]:ABORt 26
- [:BENCh][:SELected]:NAME 26
- [:BENCh][:SELected]:NUMBer 26
- [:BENCh][:SELected]:STRing 27
- [:BENCh]:TAG 28
- CALibration Subsystem 29
- :CALibration[:SMU]:ZERO[:ON] 30
- :CALibration[:SMU]:ZERO:PLC 31
- RESult Subsystem 32
- :RESult:FORMat 33
- :RESult:FORMat:ESCape 33
- :RESult:RECycle:ALL 34
- :RESult:RECycle[:LATest] 34
- STANDby Subsystem 35
- SYSTem Subsystem 36
- WORKspace Subsystem 37
- :WORKspace[:SELected]:NAME? 38
- :WORKspace:STATe? 38
- Error Messages 39
- 7 Utilities 41
- System Requirements 43
- Desktop EasyEXPERT 44
- About Desktop EasyEXPERT 45
- To Install Desktop EasyEXPERT 46
- To Start Desktop EasyEXPERT 47
- Execution Mode dialog box 47
- Start EasyEXPERT window 48
- Using 4155B/4156B/4155C/4156C 50
- License Management Tool 53
- License Management Tool GUI 54
- Setup File Converter 55
- Setup File Converter GUI 56
- MDM File Converter 57
- MDM File Converter GUI 58
- Utility Programs 59
- SetupFileConverter.exe 60
- MdmFileConverter.exe 63
- Utilities 72
- 8 Application Library 77
- Application Test Definitions 79
- Application Library 81
- Accuracy 91
- Capacitance (F) 92
- Capa citance (F) 93
- HRSMU, ASU+SMU 94
- Measurement Accuracy 95
- Reading Accuracy (%) 102
- Offset Accuracy (F) 102
- 9 If You Have a Problem 127
- When You Operate B1500 129
- ASU is not Detected 130
- To Simplify the Connections 131
- When You Perform Measurement 132
- )HUULWHEHDGV 134
- 7HVWGHYLFH 134
- Measurement 136
- To Make Backup 138
- To Check Module Slots 138
- To Check ASU/SMU Combination 138
- Data Backup and Recovery 140
- Folders to Backup 141
- To Make Database Backup 141
- To Restore Database Backup 142
- To Make Backup of Other Data 143
- B1500 System Recovery 144
- To Initialize Database 146
- To Restore Database 147
- Updating EasyEXPERT 148
- If You Have a Problem 150
- 10 Error Message 151
- Agilent FLEX Execution Error 182
- DAC test 209
- 3465 IM short test failed 213
- *B1540-90020* 228
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies EasyEXPERT
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels