Agilent Technologies EasyEXPERT Guide de l'utilisateur Page 201
- Page / 228
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Agilent EasyEXPERT User’s Guide Vol. 2, Edition 1 10-51
Error Message
Agilent FLEX Execution Error
3051 Measurement data FIFO overflow error.
ALWG sequencer run time error. WGFMU module FIFO overflow
occurred because the averaging count was frequently changed.
3052 Measurement range change request error.
ALWG sequencer run time error. Measurement range cannot be
changed because the range change interval is too short.
3201 ALWG Sequence Data is not ready.
Sequence data must be set to the specified WGFMU channel.
3202 ALWG Waveform Data is not ready.
Waveform data must be set to the specified WGFMU channel.
3301 Specified output voltage is out of absolute limits.
Check the output voltage and set the correct value. The value must be
-3 V to +3 V for the 3 V range, -5 V to +5 V for the 5 V range, -10
V
to 0 V for the -10 V range, or 0 V to +10 V for the + 10 V range.
3302 Specified voltage output range is invalid.
Check the voltage output range and set the correct value.
3303 Invalid measurement mode for current operation mode.
Operation mode must be Fast IV or DC to perform current
measurement.
3304 Specified ALWG Vector Data size is out of absolute limits.
ALWG data cannot be read because of too large data size.
3305 Specified ALWG Sequence Data size is out of absolute limits.
ALWG data cannot be read because of too large sequence data size.
3306 ALWG Waveform Data is empty.
ALWG data must not be empty.
3307 Specified ALWG Waveform Data size is out of absolute limits.
ALWG data cannot be read because of too large waveform data size.
3308 Specified waveform index of ALWG Sequence Data is out of absolute
limits.
Check the index value of the sequence data and set the correct value.
- Keysight EasyEXPERT Software 1
- For B1500A Users 5
- For B1505A Users 5
- In This Manual 6
- Contents 10
- 6 Remote Control Interface 13
- Sample programs 14
- About socket services 14
- Introduction 15
- Supported Operations 16
- Preparation for Communication 17
- Common Commands 22
- BENCh Subsystem 23
- [:BENCh]:COUNt:RESet 24
- [:BENCh]:LOAD[:SETup] 24
- [:BENCh]:PRESet:CATalog? 24
- [:BENCh]:PRESet:OPEN 24
- [:BENCh]:PRESet:SETup:SELect 25
- [:BENCh][:SELected]:ABORt 26
- [:BENCh][:SELected]:NAME 26
- [:BENCh][:SELected]:NUMBer 26
- [:BENCh][:SELected]:STRing 27
- [:BENCh]:TAG 28
- CALibration Subsystem 29
- :CALibration[:SMU]:ZERO[:ON] 30
- :CALibration[:SMU]:ZERO:PLC 31
- RESult Subsystem 32
- :RESult:FORMat 33
- :RESult:FORMat:ESCape 33
- :RESult:RECycle:ALL 34
- :RESult:RECycle[:LATest] 34
- STANDby Subsystem 35
- SYSTem Subsystem 36
- WORKspace Subsystem 37
- :WORKspace[:SELected]:NAME? 38
- :WORKspace:STATe? 38
- Error Messages 39
- 7 Utilities 41
- System Requirements 43
- Desktop EasyEXPERT 44
- About Desktop EasyEXPERT 45
- To Install Desktop EasyEXPERT 46
- To Start Desktop EasyEXPERT 47
- Execution Mode dialog box 47
- Start EasyEXPERT window 48
- Using 4155B/4156B/4155C/4156C 50
- License Management Tool 53
- License Management Tool GUI 54
- Setup File Converter 55
- Setup File Converter GUI 56
- MDM File Converter 57
- MDM File Converter GUI 58
- Utility Programs 59
- SetupFileConverter.exe 60
- MdmFileConverter.exe 63
- Utilities 72
- 8 Application Library 77
- Application Test Definitions 79
- Application Library 81
- Accuracy 91
- Capacitance (F) 92
- Capa citance (F) 93
- HRSMU, ASU+SMU 94
- Measurement Accuracy 95
- Reading Accuracy (%) 102
- Offset Accuracy (F) 102
- 9 If You Have a Problem 127
- When You Operate B1500 129
- ASU is not Detected 130
- To Simplify the Connections 131
- When You Perform Measurement 132
- )HUULWHEHDGV 134
- 7HVWGHYLFH 134
- Measurement 136
- To Make Backup 138
- To Check Module Slots 138
- To Check ASU/SMU Combination 138
- Data Backup and Recovery 140
- Folders to Backup 141
- To Make Database Backup 141
- To Restore Database Backup 142
- To Make Backup of Other Data 143
- B1500 System Recovery 144
- To Initialize Database 146
- To Restore Database 147
- Updating EasyEXPERT 148
- If You Have a Problem 150
- 10 Error Message 151
- Agilent FLEX Execution Error 182
- DAC test 209
- 3465 IM short test failed 213
- *B1540-90020* 228
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies EasyEXPERT
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.588 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels