Agilent Technologies EasyEXPERT Guide de l'utilisateur Page 153
- Page / 228
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Agilent EasyEXPERT User’s Guide Vol. 2, Edition 1 10-3
Error Message
Agilent EasyEXPERT Operation Error
Agilent EasyEXPERT Operation Error
When Agilent B1500 causes errors in Agilent EasyEXPERT execution
environment, the B1500 returns the following error codes and error messages.
101001 Log repository operation failed.
101002 Log file operation failed.
101003 Log record operation failed.
102001 Service started successfully.
102002 Service stopped successfully.
102003 Service starting process failed. Contact your nearest Agilent
Technologies.
102004 Service stopping process failed. Contact your nearest Agilent
Technologies.
103001 USB488 error occurred. Alias: A, Reason: B
103002 USB488 device was not found. Alias: A, Reason: B
103003 USB488 timeout occurred. Alias: A, Timeout: B [ms]
103004 GPIB error occurred. Interface: A, Address: B, Reason: C
103005 GPIB address must be between 0 and 31. Interface: A, Address: B
103006 Duplicate GPIB address was found. GPIB address must be unique.
Interface: A, Address: B
103007 GPIB device was not found. Interface: A, Address: B, Reason: C
103008 GPIB timeout occurred. Interface: A, Address: B, Timeout: C [ms]
104001 Module (A) is not available.
105001 Generic setup error occurred. Code: A, Reason: B
105002 Duplicate data name was found. Data name must be unique. Data
name: A
105003 Operation is not supported in offline mode.
105004 Interlock circuit is open. Interlock circuit must be closed for setting
voltage source/compliance absolute value exceeding 42V.
105005 Output series resistor cannot be used for SMU with ASU.
- Keysight EasyEXPERT Software 1
- For B1500A Users 5
- For B1505A Users 5
- In This Manual 6
- Contents 10
- 6 Remote Control Interface 13
- Sample programs 14
- About socket services 14
- Introduction 15
- Supported Operations 16
- Preparation for Communication 17
- Common Commands 22
- BENCh Subsystem 23
- [:BENCh]:COUNt:RESet 24
- [:BENCh]:LOAD[:SETup] 24
- [:BENCh]:PRESet:CATalog? 24
- [:BENCh]:PRESet:OPEN 24
- [:BENCh]:PRESet:SETup:SELect 25
- [:BENCh][:SELected]:ABORt 26
- [:BENCh][:SELected]:NAME 26
- [:BENCh][:SELected]:NUMBer 26
- [:BENCh][:SELected]:STRing 27
- [:BENCh]:TAG 28
- CALibration Subsystem 29
- :CALibration[:SMU]:ZERO[:ON] 30
- :CALibration[:SMU]:ZERO:PLC 31
- RESult Subsystem 32
- :RESult:FORMat 33
- :RESult:FORMat:ESCape 33
- :RESult:RECycle:ALL 34
- :RESult:RECycle[:LATest] 34
- STANDby Subsystem 35
- SYSTem Subsystem 36
- WORKspace Subsystem 37
- :WORKspace[:SELected]:NAME? 38
- :WORKspace:STATe? 38
- Error Messages 39
- 7 Utilities 41
- System Requirements 43
- Desktop EasyEXPERT 44
- About Desktop EasyEXPERT 45
- To Install Desktop EasyEXPERT 46
- To Start Desktop EasyEXPERT 47
- Execution Mode dialog box 47
- Start EasyEXPERT window 48
- Using 4155B/4156B/4155C/4156C 50
- License Management Tool 53
- License Management Tool GUI 54
- Setup File Converter 55
- Setup File Converter GUI 56
- MDM File Converter 57
- MDM File Converter GUI 58
- Utility Programs 59
- SetupFileConverter.exe 60
- MdmFileConverter.exe 63
- Utilities 72
- 8 Application Library 77
- Application Test Definitions 79
- Application Library 81
- Accuracy 91
- Capacitance (F) 92
- Capa citance (F) 93
- HRSMU, ASU+SMU 94
- Measurement Accuracy 95
- Reading Accuracy (%) 102
- Offset Accuracy (F) 102
- 9 If You Have a Problem 127
- When You Operate B1500 129
- ASU is not Detected 130
- To Simplify the Connections 131
- When You Perform Measurement 132
- )HUULWHEHDGV 134
- 7HVWGHYLFH 134
- Measurement 136
- To Make Backup 138
- To Check Module Slots 138
- To Check ASU/SMU Combination 138
- Data Backup and Recovery 140
- Folders to Backup 141
- To Make Database Backup 141
- To Restore Database Backup 142
- To Make Backup of Other Data 143
- B1500 System Recovery 144
- To Initialize Database 146
- To Restore Database 147
- Updating EasyEXPERT 148
- If You Have a Problem 150
- 10 Error Message 151
- Agilent FLEX Execution Error 182
- DAC test 209
- 3465 IM short test failed 213
- *B1540-90020* 228
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies EasyEXPERT
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels