Agilent Technologies EasyEXPERT Guide de l'utilisateur Page 197
- Page / 228
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Agilent EasyEXPERT User’s Guide Vol. 2, Edition 1 10-47
Error Message
Agilent FLEX Execution Error
1015 Modules set to PCH must be different.
Same module was specified by PCH for both master and slave HCSMU
modules. They must be the different modules.
1016 Do not execute CN/CNX to the slave module set to PCH.
Specify the master module in CN/CNX to enable the dual HCSMU
channel.
1017 Specified module is already used for dual HCSMU.
Specify a free HCSMU.
1018 Total setting current exceeds the capacity of main frame power supply.
Reduce setting current.
Set the current lower than the specified value.
2000 SPGU module does not exist.
The SPGU channel number must be specified correctly.
2001 SPGU channel does not exist.
The SPGU channel number must be specified correctly.
2002 SPGU signal source does not exist.
The SPGU signal source number must be specified correctly.
2003 SPGU operation mode must be PG. (SIM 0).
2004 SPGU operation mode must be ALWG (SIM 1).
2051 Over voltage emergency occurred.
All modules stopped their output and opened their output relay.
2052 Over current emergency occurred.
All modules stopped their output and opened their output relay.
2053 High temperature emergency occurred.
All modules stopped their output and opened their output relay.
2054 Over voltage H/W SRQ detected.
Specified module stopped the output and opened the output relay.
2055 Over current H/W SRQ detected.
Specified module stopped the output and opened the output relay.
- Keysight EasyEXPERT Software 1
- For B1500A Users 5
- For B1505A Users 5
- In This Manual 6
- Contents 10
- 6 Remote Control Interface 13
- Sample programs 14
- About socket services 14
- Introduction 15
- Supported Operations 16
- Preparation for Communication 17
- Common Commands 22
- BENCh Subsystem 23
- [:BENCh]:COUNt:RESet 24
- [:BENCh]:LOAD[:SETup] 24
- [:BENCh]:PRESet:CATalog? 24
- [:BENCh]:PRESet:OPEN 24
- [:BENCh]:PRESet:SETup:SELect 25
- [:BENCh][:SELected]:ABORt 26
- [:BENCh][:SELected]:NAME 26
- [:BENCh][:SELected]:NUMBer 26
- [:BENCh][:SELected]:STRing 27
- [:BENCh]:TAG 28
- CALibration Subsystem 29
- :CALibration[:SMU]:ZERO[:ON] 30
- :CALibration[:SMU]:ZERO:PLC 31
- RESult Subsystem 32
- :RESult:FORMat 33
- :RESult:FORMat:ESCape 33
- :RESult:RECycle:ALL 34
- :RESult:RECycle[:LATest] 34
- STANDby Subsystem 35
- SYSTem Subsystem 36
- WORKspace Subsystem 37
- :WORKspace[:SELected]:NAME? 38
- :WORKspace:STATe? 38
- Error Messages 39
- 7 Utilities 41
- System Requirements 43
- Desktop EasyEXPERT 44
- About Desktop EasyEXPERT 45
- To Install Desktop EasyEXPERT 46
- To Start Desktop EasyEXPERT 47
- Execution Mode dialog box 47
- Start EasyEXPERT window 48
- Using 4155B/4156B/4155C/4156C 50
- License Management Tool 53
- License Management Tool GUI 54
- Setup File Converter 55
- Setup File Converter GUI 56
- MDM File Converter 57
- MDM File Converter GUI 58
- Utility Programs 59
- SetupFileConverter.exe 60
- MdmFileConverter.exe 63
- Utilities 72
- 8 Application Library 77
- Application Test Definitions 79
- Application Library 81
- Accuracy 91
- Capacitance (F) 92
- Capa citance (F) 93
- HRSMU, ASU+SMU 94
- Measurement Accuracy 95
- Reading Accuracy (%) 102
- Offset Accuracy (F) 102
- 9 If You Have a Problem 127
- When You Operate B1500 129
- ASU is not Detected 130
- To Simplify the Connections 131
- When You Perform Measurement 132
- )HUULWHEHDGV 134
- 7HVWGHYLFH 134
- Measurement 136
- To Make Backup 138
- To Check Module Slots 138
- To Check ASU/SMU Combination 138
- Data Backup and Recovery 140
- Folders to Backup 141
- To Make Database Backup 141
- To Restore Database Backup 142
- To Make Backup of Other Data 143
- B1500 System Recovery 144
- To Initialize Database 146
- To Restore Database 147
- Updating EasyEXPERT 148
- If You Have a Problem 150
- 10 Error Message 151
- Agilent FLEX Execution Error 182
- DAC test 209
- 3465 IM short test failed 213
- *B1540-90020* 228
Produits connexes et manuels pour Mesure, test et contrôle Agilent Technologies EasyEXPERT
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.157 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels