Agilent Technologies HP 8566B Spécifications Page 354

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 405
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 353
24. Digital Storage Display Adjustments
11.
12.
Sample
and
Hold
13.
Balance
Adjustments
14.
15.
16.
17.
18.
Adjust
A3A3R8
YSL so that the vertical graticule lines just
meet the horizontal graticule lines at the top and bottom of the
graticule.
Repeat steps 10 and 11 until horizontal and vertical graticule lines
are adjusted so that they meet at the edges of the graticule but do
not overshoot.
Set spectrum analyzer LINE switch to STANDBY.
Place
A3A3
Line Generator on extender boards.
Set spectrum analyzer LINE switch to ON. Press
C2-221.
Key in (SHIFT)
0
Z
(RECORDER LOWER LEFT) 0
IHz).
Press (SHIFT)
0
1
(RECORDER UPPER RIGHT) 1028
IHL).
Set the oscilloscope controls as follows:
Press
ICHANl
Channel 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .on
probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1O:l
amplitude scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 mV/div
offset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
..O
V
coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
..dc
Channel 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . off
probe
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1O:l
amplitude scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...2
V/div
offset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
..OV
coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
..dc
Press (TRIG)
source
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Channel 4
level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.300
mV,
edge
Press
CTlME]
time scale
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
ns/div
delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -400 ns
Press
[DISPLAY)
connect dots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
..on
Press
L-1
Adjust
A3A2R50
X S&H BAL for minimum dc offset between
the level of the signal inside the two pulses to the signal level
outside the two pulses. Figure 3-106 shows a properly adjusted
waveform. Figure 3-107 shows the waveform before adjustment.
Refer to Figure 3-105 for location of adjustment.
3-214 Adjustments
Vue de la page 353
1 2 ... 349 350 351 352 353 354 355 356 357 358 359 ... 404 405

Commentaires sur ces manuels

Pas de commentaire